NO |
Maker |
Model |
Description |
1 |
Advantest |
R3261D |
9kHz-3.6GHz with 1Hz maximum resolution. Specialized signal measurement modes including RF power. |
2 |
AC/DC |
EL300 |
Electronic load. 300Wt max. Hi/Low range, small size |
3 |
Acterna |
TTC-310 |
Protocol analyzer with DS1/DS3 interface; opt 1 and 3 |
4 |
Acterna |
8630 |
Protocol analyzer GSM, GPRS, CDMA, UMTS, V5, ISDN, SS#7. Operating system not loaded! E1/T1 interface available |
5 |
Acterna |
4000 |
Communication analyzer. Two interface slots allow mixing of different test modules in one analyzer. |
6 |
Acterna |
6000A |
Communication analyzer. Inteface modules are available. |
7 |
Acterna |
6005 |
GPIB Inteface module for TTC6000A analyzer |
8 |
Acterna |
40200 |
RS-449 interface for the TTC 4000, 6000 analyzers |
9 |
Acterna |
40202 |
V.35 Interface module for TTC 4000, 6000 analyzers |
10 |
Acterna |
40204 |
Interface module for TTC 4000, 6000 analyzers |
11 |
Acterna |
40895 |
T1 channel monitor for TTC209 |
12 |
Acterna |
41440 |
T1/FT1 interface for the TTC6000 analyzer. Unused condition |
13 |
Acterna |
41440A |
T1/FT1 interface for the TTC6000A analyzer. |
14 |
Acterna |
41704-01 |
V35 inteface plug-in for TTC 6000 |
15 |
Acterna |
2262/90.01 |
Acterna E1/T1 Module for the Acterna 8630 analyzer |
16 |
Acterna |
ANT-20SE |
With STM-64 and OC-192 Interface module. Contact us for the list of installed options. |
17 |
Acterna |
310 |
Communication Analyzer. With option S.. Options are available separately |
18 |
Adtech |
AX/4000 |
10GB Ethernet test system. Incl. 16slot chassi, 401427 control module, 403100 Generator/Analyzer, 403335 Test interface |
19 |
Adtech |
403335 |
Test interface for Adtech AX/4000 system |
20 |
Adtech |
401427 |
Control module for AX/4000 system. |
21 |
Adtech |
403100 |
Generator/Analyzer module for AX/4000 system. |
22 |
Advantest |
TR4131 |
10kHz-3.5GHz portable spectrum analyzer. GPIB, RS-232, Video out, Audio jack. . |
23 |
AgiHP |
6443B |
0-120V, 0-2.5A. Constant voltage or current. Fine adjustment controls. |
24 |
Agilent |
1670D |
136 channel, 100MHz/250MHz, Deep memory logic analyzer. 1MB per channel, Ethernet port |
25 |
Agilent |
1672E |
68 channel, 100MHz/250MHz, Deep memory logic analyzer. 1MB per channel Hard drive, Ethernet port |
26 |
Agilent |
E4406A |
Communication Analyzer. Option BAC ( CDMA measurement personality ) |
27 |
Agilent |
4155A |
Repair Service. |
28 |
Agilent |
4155B |
Semiconductor Parameter Analyzer. 4 SMU’s and 2 VSU’s, Color Graphics. |
29 |
Agilent |
4156B |
Semiconductor Parameter Analyzer. 4 HiRes SMU’s and 2 VSU’s, Color Graphics. |
30 |
|
4155A |
|
31 |
Agilent |
4155B |
Repair Service. |
32 |
Agilent |
4155C |
Repair Service. |
33 |
Agilent |
4156A |
Repair Service. |
34 |
Agilent |
4156C |
Repair Service. |
35 |
Agilent |
86130A |
BERT Analyzer 3.5GigaBit/s. Pattern generator and Error Detector. Windows GUI. |
36 |
Agilent |
33120A |
15MHz Functions/Arbitrary waveform generator. New in a box! |
37 |
Agilent |
8493A |
12.5GHz attenuator. SMA connectors. Available values: 3,6,10,20,30dB |
38 |
Agilent |
8494B |
Programmable step attenuator, DC-18GHz, 11dB, “N” connectors (opt 002) |
39 |
Agilent |
8494G |
Programmable step attenuator, DC-4GHz, 11dB, SMA conn. 5VDC. opt 002, 011 |
40 |
Agilent |
8495G |
Programmable step attenuator, DC-4GHz, 70dB, SMA conn.. 5VDC opt 002, 011 |
41 |
Agilent |
8495H |
Programmable step attenuator, DC-18GHz, 70dB, SMA connectors (opt 002) |
42 |
Agilent |
33320H |
Programmable step attenuator, DC-18 GHz, 11dB, SMA conn. Sold as set of 2 |
43 |
Agilent |
33321H |
Programmable step attenuator, DC-18 GHz, 70dB, SMA conn. Sold as a set of 2 |
44 |
Agilent |
33322H |
Programmable step attenuator, DC-18 GHz, 70dB, SMA conn., 24VDC. |
45 |
Agilent |
33322H |
Programmable step attenuator, DC-18 GHz, 70dB, SMA connectors, 24VDC. |
46 |
Agilent |
10833A |
GPIB/IEEE-488 Cable. MSRP . Multiple quantity discount. |
47 |
Agilent |
10833B |
GPIB/IEEE-488 Cable, 2 meter length (6ft). Multiple quantity discount. |
48 |
Agilent |
10833C |
GPIB/IEEE-488 Cable, 4 meter length (13ft). Multiple quantity discount. |
49 |
Agilent |
N2262A |
Multiplexer card for Agilent data acquisition systems. Connector block included |
50 |
Agilent |
N2266A |
Multiplexer board for Agilent data acquisition systems. Connector block included |
51 |
Agilent |
82340A |
GPIB-16 bit board for PC. |
52 |
Agilent |
3497A |
Switch/Control Unit. GPIB,. Cards are availabled separately |
53 |
Agilent |
3499B |
Switch/Control Unit. GPIB, RS-232, 2 Card slots |
54 |
Agilent |
44476A |
RF switch card for the HP3488A, 3499A switch unit. |
55 |
Agilent |
54845B |
1.5GHz, 8Gs/s, 4 channel, Color, USB, GPIB, CDROM, FDD.. |
56 |
|
5062-7345 |
Rack mount kit for the Agilent & HP 54600 series oscilloscopes. |
57 |
Agilent |
E2613A |
Wedge Probe Adapter for TQFP and PQFP, 3 Signal. New in a box. |
58 |
Agilent |
E2614A |
Wedge Probe Adapter for TQFP and PQFP, 8 Signal. 0.5mm pitch. New in a box. |
59 |
Agilent |
E2615A |
Wedge Probe Adapter for TQFP and PQFP, 3 Signal. New in a box. |
60 |
Agilent |
E3642A |
0-8V, 0-5A or 8-20V at 0-2.5A. NEW EQUIPMENT. |
61 |
Agilent |
66101A |
0-8V, 0-16A, programmable plug-in for the Agilent 66000A mainframe |
62 |
Agilent |
E3615A |
0-20V, 0-3A. Digital displays… |
63 |
Agilent |
6632B |
0-20V, 0-5A. Programmable power supply. 4.5 digit resolution. GPIB & RS232 interfaces. Free rack mount kit. |
64 |
Agilent |
6544A |
0-60V, 0-3.5A! |
65 |
Agilent |
E3612A |
0-120V, 500mA below 60V, 250mA above 60V. Constant voltage or current. 3.5 digit displays. |
66 |
Agilent |
6645A |
0-120V, 0-1.5A. 3.5 digit setting accuracy. GPIB interface. Digital and analog front panel controls |
67 |
Agilent |
G3170-80018 |
Bipolar HED power supply for the Agilent 5975 GC systems. Applied Kilovolts p/n HF007PZZ425 |
68 |
Agilent |
G1969-80108 |
Detector power supply for TOF III. Applied Kilovolts p/n HP010RZZ366 |
69 |
Agilent |
E3004-61030 |
Power supply for Agilent 94000 analog IC tester. |
70 |
Agilent |
J2904A |
Internet Advisor ISDN module. New in a box with software and cables |
71 |
American Reliance |
AR-180T |
Transmission loss tester. Handheld tester with DMM function. Combines a 0dBm/-13dBm transmitter and AC voltmeter with dB scale. Olso measures DCV, and Ohms |
72 |
American Reliance |
AR-180T |
Transmission loss tester with DMM function. Combines a 0dBm/-13dBm transmitter and AC voltmeter with dB scale. Olso measures DCV, and Ohms |
73 |
American Reliance |
AR-180T |
Transmission loss tester. Handheld tester with DMM function. Combines a 0dBm/-13dBm transmitter and AC voltmeter with dB scale. Olso measures DCV, and Ohms |
74 |
Ameritec |
AM5 |
Transmission Impairment Measurement Set. Runs on AC or battery power . |
75 |
Ameritec |
AM8A |
PCM/VF Call analyzer. Computer interface. Runs on AC or a built in rechargable battery |
76 |
Amprobe |
A50-1 |
Current transformer. Extend the range of your clamp-on AC current probe to 1200A. With carrying case. |
77 |
Amrel |
SPS20-60-002 |
0-20V, 0-60A. Digital displays, only 1.5″ high, 19″ rack ready. optional GPIB interface. |
78 |
Amrel |
PPS-1322 |
0-30V, 0-2V programmable power supply. 1mV, 1mA meter resolution, GPIB interface. sold |
79 |
Andy Gish |
ESD255 |
ESD Generator. 25kV, Event counter, Manual or variable repetition rate, External trigger input. Specs |
80 |
Anritsu |
41KA-6 |
Attenuator 6 dB, 2Wt, DC-18GHz, NEW! QIV |
81 |
Anritsu |
41KA-20 |
Attenuator 20dB, 2Wt, DC-18GHz, NEW! |
82 |
B&K |
1670A |
0-30V, 0-3A, 5V @ 0.5A, 12V @ 0.5A Digital V & A readouts.. iii |
83 |
B&K |
1050 |
Universal telephone analyzer. Test telephones, faxes, modems, answ mach. etc. |
84 |
B&K Precision |
1660 |
2x 0-30V @ 2A ea. and 4-6.5V @ 5A. Tracking mode. Series/Parallel LED displays. |
85 |
Bertan |
105-03R |
3kV, 333mA, Constant current or voltage mode. Reversable polarity, digital display, remote analog programming. |
86 |
Bertan |
105-30R |
30kV, 33mA, Constant current or voltage mode. digital display, high resolution V/I controls, remote analog |
87 |
Biorad |
200/2.0 |
0-200V, 0-2A. 200Wt max. CV or CC mode. Programmable On/Off time. |
88 |
Bio-Rad |
760 |
Switcher for Pulsed DNA electrophoresis. Switches up to760VDC at programmable time intervals from 0.1-99,999sec. |
89 |
Bird |
43 |
RF Wattmeter. 100mW-10kW, 450kHz-2700MHz (element dependent). Free 50Wt, 2MHz-30MHz slug! |
|
90 |
BK |
1803B |
100MHz handheld frequency counter. Rechargable or AA batt. and AC operation. |
91 |
BK |
1050 |
Universal telephone analyzer. Test telephones, faxes, modems, answ mach. etc. |
92 |
BK Precision |
3017A |
2MHz Sweep/Function Generator with Main, TTL and CMOS outputs. 20V p-pk |
93 |
BMI |
4800 |
AC power analyzer and data recorder. Detect virtually any type of problem with AC power. |
94 |
BMI |
A600 |
AC current probe. 600A contunuous current capacity. For BMI power analyazers. |
95 |
Boonton |
4400A |
RF Peak Power Analyzer. Repair service. Flat rate |
96 |
Boonton |
4400L |
RF Peak Power Analyzer. Repair service. Flat rate |
97 |
Boonton |
72BD |
Capaciance Meter, 1MHz test freq., Digital display, 0.01pF resolution. With a test fixture |
98 |
California Instruments |
1001T |
AC power source, 1000 Watt, 100-270VAC, 45Hz -5kHz , 8000T oscillator |
99 |
Clarke-Hess |
263 |
Watt, Power Factor meter. Plus ACA & VAC. Digital. Requires current transformer |
100 |
Colby Instruments |
CPLD |
Programmable delay line 10pS to100pS. GPIB interface. Optional rack-mount kit included. |
101 |
Cole-Parmer |
1481-61 E-C |
E-C Meter & DIP cell probe. Six ranges, automatic temp compensation mode |
102 |
Consultronics |
DLS200 |
Wireline simulator for DSL and ISDN with Impairment generator option. 10 standard test loops plus crosstalk, impulse, powerline and longitudal noise impairments |
103 |
Data Check |
5010-ACP |
XYZ display. Substitute HP model. |
104 |
Datapulse |
201 |
Data-Pulse generator. Generate 16 bit serial data streams up to 10 MHz. Adjustable amplitude 0-10V and offset: +/-10V. Manual or Auto trigger. Sync clock outputs. requires external drive signal sinewave ( 1Vrms) or squarewave ( +/-0.5V). |
105 |
DATRON |
1082 |
7.5 digit DMM. AC/DC, Ohm, GPIB. |
106 |
Dranetz |
606-1 |
600 VAC max. Detects and measures Impulse, Sag/Surge, Slow Average. Clock with backup records time of of the event. Automatically prints disturbance information. Built in printer. |
107 |
Dranetz |
626-PA-
6002 |
DC voltage monitoring module for Dranetz 626 power analyzer |
108 |
Dranetz |
626-PA-
6003 |
AC voltage monitoring module for Dranetz 626 power analyzer |
109 |
Dranetz |
626-PA-
6006 |
AC neutral line monitoring board for Dranetz 626 power analyzer |
110 |
Dranetz |
626-PA-
6030 |
AC Graphics monitor for Dranetz 626 analyzer |
111 |
Dranetz |
808 |
Power demand analyzer with built in printer. Accurate record of power consumption over time |
112 |
Dwyer |
470 |
Dwyer Thermal Anemometer. Low range:0.2-3 m/s, High range: 2-30 m/s. With probe. |
113 |
Eaton |
384M |
1MHz – 4GHz., Synthesized signal generator , +18.5dBm max. power, Digital sweep, FSK/ FM/ AM/Phase modulation. 1Hz max resolution. PC programmable. With optional Eaton 255 modulator. Other plug-ins avail. |
114 |
EG&G |
410 |
C-V plotter for silicone wafer analysis. Built in 1MHz capacitance meter |
115 |
EG&G |
5101 |
Lock-in amplifier. 5Hz-100kHz, 1uV-500mV. |
116 |
EIP |
545A |
18GHz , -30dB sensitivity 12 digit resolution. Option 8 (GPIB). Up to 100 meas/sec.. |
117 |
EIP |
548A |
26.5GHz Microwave counter. Covers 10MHz to 26.5GHz frequency range.. |
118 |
EIP |
548B |
110GHz Microwave counter. Option 6 included. GPIB interface. . wj. |
119 |
EIP |
575 |
18GHz Source Locking Microwave counter with GPIB Interface. Opt 9 (rear input).. |
120 |
Elgar |
1001SL |
AC power source 2000VA, 0-260VAC, 45Hz to 5kHz variable frequency SD400 plug-in. |
121 |
Elgar |
1751SX-14 |
AC power source with 9012 variable frequency plug-in and GPIB interface |
122 |
Elgar |
9012 |
Variable frequency plug-in for Elgar 1751SX AC power source |
123 |
ELGEN |
1000 |
DC-2MHz, 170V p-pk output. 10mA max. High voltage pulse generator or high voltage sinewave. |
124 |
EMI |
EMS7.5-75-1-D |
0-7.5V, 0-75A, Constant current or voltage mode. Only 1.5″ high. Digital high resolution displays. |
125 |
EMI |
EMS10-60-1-D |
0-10V, 0-60A, Constant current or voltage mode. Only 1.5″ high. Digital high resolution displays. |
126 |
EMI |
EMS40-125-2-D |
0-40V, 0-125A, Constant current or voltage mode. Digital high resolution. Requires 3 phase AC. |
127 |
EMS |
TCR7.5S300 |
0-7.5V, 0-300A, Constant current or voltage mode. FREE GPIB controller! For use on 190-250VAC lines |
128 |
EMS |
ESS-40-25 |
0-40V, 0-25A, Constant voltage or current mode. LCD displays, 1.5″ height. (add GPIB) |
129 |
Fluke |
1953A |
Universal Counter. 100MHz, dual channel. Options: 5,14,15,16. Rack mount kit available |
130 |
FLUKE |
77 III |
DMM. True RMS, Frequency, Capacitance, 10A current, Display with bargraph. |
131 |
FLUKE |
8000A |
3.5 Digit Bench DMM. Measures voltages up to 1200V RMS |
132 |
FLUKE |
8050A |
4.5 Digit Bench DMM dBm, Conductance, True RMS SOLD |
133 |
FLUKE |
8840A |
5.5 digit, System DMM. DC voltage/current and Ohms only. option for AC and GPIB sold |
134 |
FLUKE |
8842A |
5.5 digit, System DMM. AC-DC voltage/current (opt 09). GPIB interface (opt 05).. |
135 |
FLUKE |
8506A |
6.5 digit, System DMM. with options 02A/09 (GPIB and Ohm’s. No ACV |
136 |
Fluke |
80k-40 |
High voltage probe. Measure DC voltages up to 40kV with any digital multimiters |
137 |
Fluke |
90i-610S |
AC-DC current probe. 2 to 600A, 40Hz-400Hz. Works with any DMM or an oscilloscope. Retail price: |
138 |
FLUKE |
6011A |
11MHz Synthesized Programmable Function Generator. GPIB interface. |
139 |
Fluke |
6160B |
Frequency Synthesizer 1-160MHz, Opt 002 (Hi stability time base), 13dBm max output. |
140 |
Fluke |
PM5418TD |
Video Signal Generator PAL/SECAM/NTSC, 15 Sound formats, Baseband or RF out. |
141 |
Fluke |
105B |
Hand held oscilloscope/DMM. COMPLETE. 100MHz, 2 Chan., 2.5GS/s, RS-232. |
142 |
Fluke |
VP190 |
200MHz, Oscilloscope probe with accesories. New with complete set of accesories. Sold as a pair. |
143 |
Fluke |
PM2811 |
0-30V, 0-10A, 60Wt max., GPIB programmable.. |
144 |
Fluke |
686 |
Network & Cable tester. Analyze data errors as well as wiring problems with Ethernet and Token ring networks up to 100MHz |
145 |
FW Bell |
4048 |
Gauss Tesla Meter & probe. AC/DC fields, Peak hold, Auto/manual range. Handeld with LCD display. |
146 |
FW Bell |
640 |
Incremental Gauss Meter & probe. AC/DC fields from 1 to 3000 gauss. Differential probe avaliable |
147 |
FW Bell |
1776 |
Clamp-on AC, DC and AC on DC Current meter. 10, 100, 1000 A range. Peak hold. 5kHz BW, +/-1% DC or AC Accuracy. With 10A probe |
148 |
GGBoprobe |
28 |
1 GHz oscilloscope probe. With power supply |
149 |
GN Nettest |
742S |
GN Nettest 7500 plug-in. Combines a source and power meter in one module 1310-1550nm |
150 |
GN Nettest |
7500 |
OTDR. Flexible configuration with optional plug-in modules. |
151 |
GR |
1265A |
0 to 400V, 0 to 5A (200Wt max) Const. voltage or constant current mode. Line regulation 0.2%. |
152 |
G-R |
1390B |
Random noise generator, 3 ranges: 20kHz, 500kHz, 5MHz, 5V max output, 5 decades of attenuation. Pink noise |
153 |
GW Instek |
GW-830 |
100MHz, 100MS/s, 50K Samples memory. RS-232, Printer port, Video output. X-Y mode, Voltage & Time cursors. |
154 |
GW Instek |
GDS-2204 |
200MHz, 4 channel 1GS/s, 25K Samples memory. USB, Color LCD, RS-232, X-Y mode. Full Specs |
155 |
Hioki |
2101 |
Megohm meter. Measure resistances up to 500 MOhm. 400V Test voltage. Remote control, Output terminals. Pass/Fail test mode with alarm. |
156 |
Hitachi |
VC-6155 |
100 MHz, Digital-Analog combination scope. Compact size, Frequency counter. 2mV sensitvity |
157 |
Hitachi |
V-1560 |
100MHz, 2 Chan, 2mV sensitivity. One button autosetup. TV-sync trigger. 90 day warranty |
158 |
HP |
141T |
Spectrum Analyzer Mainframe. Storage mode 100% operational. |
159 |
HP |
3580A |
5Hz-50kHz. 100nV to 20V amplitude, 80dB dynamic range. Opt 002 Rechargeable batt option |
160 |
HP |
3588A |
10Hz-150MHz. Built in signal source. 0.25dB amplitude accuracy. |
161 |
HP |
8555A |
10MHz-18GHz RF section Shown with optional display unit & IF section. |
162 |
HP |
8557A |
10kHz-300MHz, 70dB attenuator, -60dBm sensitivity. Add HP 182 Large screen display oprion |
163 |
HP |
8562E |
9kHz -13GHz. Available options: 001, 005, 007, 008. Memory module included |
164 |
HP |
8568B |
100Hz-1.5GHz Synthesized accuracy delivers 10Hz resolution. Memory. RF SECTION only |
165 |
HP |
8569A |
10kHz-22GHz, Signal storage, memory, GPIB output to printer or plotter. . |
166 |
HP |
8590A |
10kHz -1.5GHz, Portable spectrum analyzer. 1 kHz resolution, opt 021 ( GPIB). New CRT . |
167 |
HP |
8591A |
10kHz -1.8GHz, Portable spectrum analyzer. 1kHz resolution, 4 digit accuracy. . |
168 |
HP |
8595E |
9kHz -6.5GHz Spectrum analyzer. 30Hz resolution. Available options: 021, 041, 140. . |
169 |
HP |
11729C |
Carrier-Noise test set. 10MHz-18GHz. Input signal: +7dBm to 20dBm. |
170 |
HP |
70904A |
RF Section for the HP 70000 series Spectrum analyzer. 100Hz-2.9GHz. |
171 |
HP |
339A |
Distortion Analyzer with built in Signal source. Signal range: 1mV-300V, 10Hz-110kHz. |
172 |
HP |
3580A |
Spectrum Analyzer. 5Hz-50kHz. 100nV to 20V amplitude, 80dB dynamic range. Opt 002 |
173 |
HP |
8903A |
Audio signal analyzer. SINAD, amplitude measurements to 110kHz. Autoranging. |
174 |
HP |
1630D |
100MHz Timing-25MHz State 43 channels. Glitch capture capability, 16 Timing channels and 27 state channels. simultaneously. |
175 |
HP |
1631D |
50MHz 200MS/s Scope & 100MHz & 43 Channel Logic analyzer. Flexible triggering. A001 |
176 |
HP |
1650A |
100MHz Timing-25MHz State 80 chan. . Menu driven user interface, Floppy |
177 |
HP |
1650B |
100MHz Timing-35MHz State 80 chan. Menu driven user interface, floppy |
178 |
HP |
1651A |
100MHz Timing-25MHz State 32 chan. ALL PROBES INCLUDED . Menu driven user interface, Floppy |
179 |
HP |
1651B |
100MHz Timing-35MHz State 32 chan. . Menu driven user interface, Floppy |
180 |
|
1653B |
100/35MHz Timing/State 32 channels with 100MHz DSO. Floppy drive storage ALL PROBES |
181 |
HP |
1661C |
500/100MHz Timing/State 102 channels 8kb/chan memory. HP Mouse. |
182 |
HP |
1662AS |
500MHz Timing-100MHz State 68 channels & 250MHz, 1Gs/s oscilloscope. 8kb/chan. Mouse, .. |
183 |
HP |
1660CS |
500/100MHz Timing/State 136 chan. & 250MHz, 1Gs/s oscilloscope. 8kb/chan. Mouse, |
184 |
HP |
16500A |
Logic Analyzer mainframe. Color 9″ CRT, floppy, 4MB memory lets you use 16550A/16555A |
185 |
HP |
16500A |
100/35MHz Timing/State 80 chan. . Color Display, FDD, 4MB memory. |
186 |
HP |
16500A |
500/100 MHz Timing/State 80 chan . . Color, floppy, Printer port, 4MB memory |
187 |
HP |
16500A |
Logic Analyzer-DSO .WITH PROBES Color, FDD, 4MB memory. Price is based on configuration. 6mo. warr. |
188 |
HP |
16500B |
Logic Analyzer 500MHz /110MHz Timing/State, 68 Chan. . 2MB memory. |
189 |
HP |
16500C |
Logic Analyzer 500MHz /110MHz Timing/State, 68 Chan. .2MB memory. |
190 |
HP |
16505A |
Prototype Analyzer. High level language debugging in windows environment for HP 16500C/D. |
191 |
HP |
16510A |
100/35MHz Timing/State, 80 channels. For HP 16500A/B/C. |
192 |
HP |
16520A |
100MHz 16 channel. . With optional 54650A GPIB interface |
193 |
HP |
16550A |
500/100 MHz Timing/State, 102 chan. 4K/8K per channel. For 16500A/B/C. |
194 |
HP |
16555A |
500/110 MHz Timing/State, 68 chan. 2MB memory. |
195 |
HP |
16555D |
500/110MHz Timing/State, 68 chan. 2MB memory. |
196 |
HP |
54620A |
16 channel logic analyzer. Automatic freq., period, hold & setup time. GPIB interface included. |
197 |
HP |
4195A |
Repair Service. |
198 |
HP |
8753A |
Network analyzer. 300kHz to 3GHz, opt 010 Time domain measurements. Bright CRT! |
199 |
HP |
8753B |
Network analyzer. 300kHz to 6GHz, opt 002, 006, 010. Excellent CRT display. |
200 |
HP |
8405A |
Vector voltmeter 1-1000MHz, 1uV-1V input, PLL capable. Sampling amp output adds 1GHz BW to any oscilloscope |
201 |
HP |
8505A |
Vector network analyzer 500kHz-1300MHz. Measure Phase, Group Delay, Gain, Attenuation, Impedance, Return Loss, S-Parameters, Reflection Coefficient, Deviation From Linear Phase and Transfer Function. |
202 |
HP |
8510B |
Network analyzer. Option 10. Eligible for Agilent trade in program for MXA & PXA analyzers. |
203 |
HP |
8755C |
Scalar Network analyzer. 3 channel, 10MHz-18.5GHz. With HP182T display. |
204 |
HP |
8757A |
Scalar Network analyzer. Opt 001, 4th Input channel. Color LCD display!. |
205 |
HP |
4145B |
Repair Service. |
206 |
HP |
4145A |
Semiconductor Parameter Analyzer. 4 SMU’s and 2 VSU’s, GPIB interface to LabView |
207 |
HP |
4145B |
Semiconductor Parameter Analyzer. 4 SMU’s and 2 VSU’s, GPIB interface to LabView |
208 |
HP |
4155A |
Semiconductor Parameter Analyzer. 4 SMU’s and 2 VSU’s, Color Graphics. |
209 |
HP |
4155B |
Semiconductor Parameter Analyzer. 4 SMU’s and 2 VSU’s, Color Graphics. |
210 |
HP |
4156B |
Semiconductor Parameter Analyzer. 4 HiRes SMU’s and 2 VSU’s, Color Graphics. |
211 |
HP |
4155A |
Repair Service. |
212 |
HP |
4155B |
Repair Service. |
213 |
HP |
4155C |
Repair Service. |
214 |
HP |
4156A |
Repair Service. |
215 |
HP |
4156C |
Repair Service. |
216 |
HP |
4194A |
Repair Service. |
217 |
HP |
83480A |
Communication analyzer mainframe. Plug-ins are available separately.. |
218 |
HP |
8750A |
Storage Normalizer unit. Adds digital storage to HP 8755, 8754A, 8505A, 8410/8412B. |
219 |
HP |
8901A |
Modulation analyzer. Measure AM/FM mod. with 1% accuracy. Also measures freq. & RF power 150kHz- 1.3GHz |
220 |
HP |
8901B |
Modulation analyzer. Measure AM/FM mod. with 1% accuracy. Measures freq. & power. 150kHz-1.3GHz. opt 001, 003 |
221 |
HP |
8970A |
Noise figure meter. Provides accurate noise measurements up to 1500MHz.IN STOCK. |
222 |
HP |
41501A |
SMU-PGU expansion unit for HP 4155A, 4156A and other Semiconductor parameters analyzers |
223 |
HP |
5314A |
100 MHz Universal Counter. Measure freq, period, ratio, time interval, totalize. 2 channels, 25mV sensitivity
Optional 001 High stability Time base ( <1 part in 10E7 |
224 |
HP |
5315A |
100MHz Universal Programmable Counter. 7 digit resolution. Measure freq., period, ratio, time interval, totalize. 2 channels, 10mV sensitivity, x1 and x20 attenuator, adj. trigger level. Options available |
225 |
HP |
5315B |
1.3GHz Universal Programmable Counter. 7 digit resolution. Period, ratio, time interval. opt 001 |
226 |
HP |
5316A |
1 GHz 3 channel Universal Programmable Counter. 8 digit resolution. Measure freq., period, ratio, time interval, |
227 |
HP |
5316B |
Two channel Universal Programmable Counter. 8 digit resolution. Measure freq., period, ratio, time interval, totalize. 10mV sensitivity, x1 and x20 attenuator, adj. trigger level.. |
228 |
HP |
5316B |
1 GHz 3 channel Universal Programmable Counter. 8 digit resolution. Measure freq., period, ratio, time interval, totalize. 10mV sensitivity, x1 and x20 attenuator, adj. trigger level. Opt 001 & 003 |
229 |
HP |
5334B |
Options 010 & 060. 9 Digits of resolution. Frequency, period, Rise/Fall time, Time interval, AC/DC voltage |
230 |
HP |
5335B |
1.3 GHz 3 channel. Option 030 & 010 or opt 020 & 040. 9 Digits of resolution. Frequency, period, Rise/Fall time, Time interval, AC/DC voltage, Pulse width, Math functions, GPIB. |
231 |
HP |
5335B |
Option 020 & 040. Frequency, period, Rise/Fall time, Time interval, AC/DC voltage, Pulse width, Math functions, GPIB. |
232 |
HP |
5345A |
Universal Counter 500MHz, 25mV sensitivity, 9000 measurements per sec. Opt 011 (GPIB interface). |
233 |
HP |
5355A |
Converter plug-in for the HP5345A counter. Extends frequency range to 40GHz |
234 |
HP |
5370A |
Time interval counter. 100MHz max, pS resolution. -1.3 to 2V trigger range, GPIB |
235 |
HP |
3478A |
5.5 digit resolution DMM. DCV, ACV, Ohms, AC/DC Curent. GPIB, Auto/Manual. SOLD |
236 |
HP |
4271B |
LCR meter. 1MHz test frequency, 3.5-digit display. Dissipation measurement. optional GPIB |
237 |
HP |
4275A |
LCR meter. 10MHz max test freq. DC Bias control (opt 001), GPIB (opt 017). 4 digit accuracy. |
238 |
HP |
4278A |
Capacitance meter. 1kHz/1MHz test frequency. opt 201 Handler interface. |
239 |
HP |
4140A |
Picoamp meter and Voltage source. Measure I, I-V and quasi-static C-V. Analog output (001), GPIB (101), |
240 |
HP |
400EL |
AC voltmeter. 10MHz, -60 to +30dBm. |
241 |
HP |
435B |
Power Meter. RF power measurements to 40GHz. Sensors & cable available separately. |
242 |
HP |
436A |
RF Power Meter with GPIB (opt. 022). 90 day warranty. Newest s/n. Eligible for Agilent trade-in program towards EMP purchase. |
243 |
HP |
438A |
RF Power Meter. Dual channel, OPT 002 (rear connectors) RF power measurements to 40GHz. GPIB, autorange. |
244 |
HP |
5004A |
Signature Analyzer Digital circuit troubleshooting tool lets you identify defective boards quickly without technical help. With leads. |
245 |
HP |
5005B |
Signature Analyzer/Voltmeter/Frequency Counter/Ohm meter in one compact unit. |
246 |
HP |
5006A |
Signature Analyzer. Digital circuit troubleshooting tool lets you identify defective boards quickly without technical help. GPIB interface (opt 040) |
247 |
HP |
8405A |
Vector voltmeter. 1-1000MHz range, 1uV-1V input, PLL capab.Also used as sampling amplifier. |
248 |
HP |
3324A |
21MHz Synthesized Programmable Sweep/Function Generator.1mHz to 21MHz @ +/-5PPM. |
249 |
HP |
3325A |
21 MHz Synthesized Programmable Sweep/Function , 1 mV to 10 V.. Option 001 available |
250 |
HP |
3325A |
21 MHz Sweep/Function generator. Opt 001 (High stability). Output: 1 mV to 10 V into 50 Ohm load |
251 |
HP |
3325B |
21MHz Synthesized Function generator. Programmable Sweep, uHz resolution, 1 mV-10 V.. |
252 |
HP |
8116A |
50MHz Pulse/Function generator. 3 digit resolution for frequency and voltage setting. Reliabity upgraded. |
253 |
HP |
8165A |
50MHz Pulse Function Generator: 1.000 mHz to 50.00 MHz. Sine, Square, Triangle, Pulse, Ramp, Modes: CW, VCO, trigger, gate, AM/FM modulation inputs and counted burst. |
254 |
HP |
8165A |
50MHz Pulse Function Generator: 1.000 mHz to 50.00 MHz. Sine, Square, Triangle, Pulse, Ramp, Modes: CW, VCO, trigger, gate, AM/FM modulation inputs and counted burst. Optional Sweep (opt 002), Rear outputs opt 003. |
255 |
HP |
8904A |
Waveform synthesizer. Opt. 001, 002. FM and Stereo Modulation, 2nd output channel, DTMF sequences. |
256 |
HP |
4 Tone Gen. |
800-900MHz, 0-30dBm output, 10kHz & 0.1dBm set point resolution, CW only. |
257 |
HP |
8350B |
Sweep oscillator mainframe. For HP 83000 and HP 86000 series plug-ins |
258 |
HP |
8656B |
Synthesized signal generator 0.1-990 MHz. -127dBm to +13dBm output. Opt.2 |
259 |
HP |
8657A |
Synthesized signal generator 0.1-1047 MHz. From -127dBm to +13dBm output . |
260 |
HP |
8657B |
Synthesized signal generator 0.1-2060 MHz. From -127dBm to +13dBm output.. |
261 |
HP |
8614A |
RF generator. 0.8-2.4GHz range. +10dBm (10mW) max power, 120dB attnuator, ext.AM/FM/Pulse |
262 |
HP |
8620C |
RF Sweep generator. Accepts plug-ins, that cover 10MHz to 22GHz range. 862XX plug-ins are listed below. GPIB interface |
263 |
HP |
83525A |
Sweep oscillator plug-in. 10MHz-8.4GHz . Late serial number.. |
264 |
HP |
83570A |
Sweep oscillator plug-in. 18GHz-26.5GHz. For HP 8350A/B sweep oscillator. |
265 |
HP |
86220A |
Sweep oscillator plug-in. Frequency range: 10MHz to 1.3GHz.. 13dBm max. output |
266 |
HP |
86222B |
Sweep oscillator plug-in. Frequency range: 10MHz to 2.4GHz.. 13dBm max. output |
267 |
HP |
86240C |
Sweep Oscillator Plug-in. 3.6 to 8.6 GHz., +20dBm For HP8620 & HP8350A/B with adapter |
268 |
HP |
86241A |
Sweep Oscillator Plug-in. 3.2 to 6.5 GHz, +8 dBm MAX level output, EXT. AM/FM mod. |
269 |
HP |
86242D |
Sweep Oscillator Plug-in. 5.9 to 9 GHz, 10 mV MAX LEVEL OUTPUT. For HP 8620 |
270 |
HP |
86260A |
Sweep Oscillator Plug-in. 12.4 to 18.0 GHz, 10 mW MAX level output. Opt 001 |
271 |
HP |
86290B |
2-18 GHz Sweeper Plug-in . Sweep or CW mode. 10 dBm max leveled output; Power variation: +/-0.9 dB internally leveled. |
272 |
HP |
86602A |
Sweep Oscillator Plug-in. 1 to 1300MHz. For HP 8660 Generator |
273 |
HP |
8007B |
100MHz, max repetition rate. Rise/Fall time <2nS-250uS, DC offset, TTL, ECL, pos/neg output |
274 |
HP |
8011A |
20MHz, Period: 50ns to 10s Pulse width: 25ns to 8 100ms. Pulse burst option 0-9999 pulse per cycle |
275 |
HP |
8012B |
50MHz. Adjustable rise & fall time time (5nS min). adjuastable DC offset for TTL, ECL, CMOS . |
276 |
HP |
8013B |
50MHz. Adjustable rise & fall time time (5nS min). adjustable DC offset for TTL, ECL, CMOS |
277 |
HP |
8015A |
50MHz. Two outputs with independent amplitude control, adjustable transition times. 1-9999 pulses burst option |
278 |
HP |
8018A |
50MHz Serial Data/PRBS Generator, 2048 bit, dual channel memory, Variable word and pattern lenght, TTL, ECL, CMOS compatible, Programmable, prbs and mixed data. HPIB interface. |
279 |
HP |
8082A |
250MHz repetition rate, 2.3nS min pulse width, 1nS rise/fall time. 5V into 50Ohm. Two outputs. |
280 |
HP |
8112A |
50MHz, adjustable transition times, burst mode, GPIB interface. Reliability upgraded |
|
281 |
HP |
8131A |
500MHz Dual channel (opt 002), <200pS transition, 5V p-pk, Jitter < 0.025%. opt 001 |
282 |
HP |
8175A |
Digital data generator. 32 TTL/CMOS channels. All pods and flying lead probes included. option 002/005 |
283 |
HP |
204D |
Sinewave oscillator 0.1Hz-1.2MHz, low distortion 600Ohm output. |
284 |
HP |
651A |
Sinewave oscillator 10Hz-10MHz, low distortion. 60dB attenuator. Newer serial number |
285 |
HP |
59308A |
GPIB timing generator. Test GPIB interface timing accuracy. |
286 |
HP |
59309A |
GPIB addressable clock. Accepts external reference signal to produce accurate time clock |
287 |
HP |
16520A |
Data pattern generator. Cables included!. Probes are available separately. II STOCK. |
288 |
HP |
16521A |
Data pattern generator. Cables included! Probes are available separately.. |
289 |
HP |
16522A |
Data pattern Vector generator for HP 16500 series analyzers. PROBES & PODS INCLUDED. option for HP16500B |
290 |
HP |
8492A |
Attenuator with APC-7 connector. Available values: 3,6,10,20db |
291 |
HP |
11713A |
Step Attenuator Switch driver. With 2 attenuator control cables. GPIB interface |
292 |
HP |
8120-2703 |
Control cables for HP Step sttenuators. Brand New |
293 |
HP |
33320H |
Programmable step attenuator, DC-18 GHz, 11dB, SMA connectors. Get HP33321H option |
294 |
HP |
33321H |
Programmable step attenuator, DC-18 GHz, 70dB, SMA connectors. Get HP33320H option |
295 |
HP |
33322H |
Attenuator DC-18GHz, 110dB max, 10 dB step. FREE CONTROL CABLE |
296 |
HP |
E1326A |
DMM card for the HP E1301A/B systems. |
297 |
HP |
E1330B |
Multiplexer card for VXI systems with terminal blocks. |
298 |
HP |
E1352A |
Multiplexer card for VXI systems; E1301B, E1302A |
299 |
HP |
E1364A |
16 Channel Form C switch. For VXI systems |
300 |
HP |
85A |
Computer with built in display and printer. With HP 82937A ( HPIB interface) |
301 |
HP |
3488A |
Switch/Control unit with GPIB interface. Up to 50 channels. DC to 26.5GHz. Cards are available separately see list below |
302 |
HP |
37203A |
HPIB Range extender. Operate GPIB or IEEE-488 instruments at greater distances. Optional fiber optic interface |
303 |
HP |
44421A |
Data acquisition input multiplexer board (20 channel) with terminal block. vii |
304 |
HP |
44422A |
T/C interface card with terminal block for HP3497A data acquisition system |
305 |
HP |
44426A |
Conter module for the HP3497A data aquisition system |
306 |
HP |
44425A |
Digital output board with terminal block. |
307 |
HP |
44428A |
Actuator interface card with terminal block for HP3497 data acquisition system |
308 |
HP |
44431A |
High voltage actuator interface card with terminal block for HP3497 data acquisition system |
309 |
HP |
44470A |
Multiplexer card with connector block for HP 3488A switch unit. ii |
310 |
HP |
44471A |
Multiplexer card with connector block for HP 3488A switch unit. iv |
311 |
HP |
44472A |
Coaxial multiplexer card for the HP3488A switch unit. |
312 |
HP |
44473A |
Relay multiplexer card for the HP3488A switch unit. New in a box. iv |
313 |
HP |
44474A |
Digital I/O card for the HP3488A switch unit. vii |
314 |
HP |
44478B |
RF multiplexer switch card for the HP3488A switch unit. ii |
315 |
HP |
44703B |
Memory card for the HP3852A DAQ unit. 1MB total memory |
316 |
HP |
44705F |
Relay multiplexer card for the HP3852A and 3853A. Newer serial number |
317 |
HP |
44710A |
T/C interface card. 20 channels. for the HP3852A and 3853A. Newer serial number |
318 |
HP |
44711A |
High speed FET multiplexer for the HP3852A/3853A.. Connector block not included. |
319 |
HP |
44724A |
16 channel digital output card for the HP3852A and 3853A.. Newer serial number |
320 |
HP |
44729A |
20 Channel multiplexer card for the HP3852A, 3853A.. Newer serial number |
321 |
HP |
44788A |
HPIB controller for HP 3582A and HP 3583A |
322 |
HP |
59301A |
ASCII to Parallel converter. Permits control of many older HP instruments via GPIB interface |
323 |
HP |
59306A |
Relay actuator. Control six form-C relays by pushbuttons or via GPIB interface |
324 |
HP |
59307A |
VHF Switch. Dual Single pole 4 throw. GPIB or pushbutton. DC-500MHz, 50 Ohm |
325 |
HP |
59501A |
Power supply programmer. Control power supplies with analog programming capabilities with a PC via GPIB interface. Isolated. Range +/-1V or +/-10V. 1mV/10mV resolution. LabView supported. |
326 |
HP |
59501B |
Power supply programmer. Control power supplies with analog programming capabilities with a PC via GPIB interface. Isolated. Range +/-1V or +/-10V. 1mV/10mV resolution. LabView supported. |
327 |
HP |
1662AS |
250 MHz, 1GS/s, 2 Chan oscilloscope with 500MHz 68Channel Logic analyzer. FDD, Mouse. |
328 |
HP |
16531A |
100 MHz, 400MS/s, 2 Channel module. For use with HP16500 logic analyzer chassis |
329 |
HP |
16532A |
250 MHz, 1GS/s, 2Chan. 8kB per channel. For use with HP16500B/C (available separately) |
330 |
HP |
54110D |
1 GHz, 2 Ch, 40 MS/s, 10 bit vertical resolution, Color, Autosetup, IEEE-488 interface |
331 |
HP |
54111D |
500 MHz, 2 CH., 2GS/s max, 8K points record, Color, Autosetup, GPIB. HP 54114A included. |
332 |
HP |
54120T |
Digital oscilloscope. 20GHz Bandwith, TDR, 4 channels HP54121A Test set with HP54120A |
333 |
HP |
54200A |
50MHz, 2 Channel, GPIB interface |
334 |
HP |
54200A |
50MHz, 2 Channel. GPIB interface. |
335 |
HP |
54501A |
100MHz, 4 channel. Auto waveform & parameter measurements, GPIB interface. |
336 |
HP |
54504A |
400MHz, 2 channel. Auto waveform & parameter measurements, GPIB |
337 |
HP |
54510A |
250MHz, 1GS/s, 2 channels. Auto waveform & parameter measurements, Autosetup. GPIB |
338 |
HP |
54520A |
500MHz, 1GS/s-500MS/s, 2 Channel, Floppy drive, Printer port. Large screen display. |
339 |
HP |
54603B |
60MHz, 20MS/s, 2 Channel, DSO. 9″ easy to read display. RS-232, GPIB, Paralle interfaces are available |
340 |
HP |
54602A |
150MHz, 20MS/s, 4 Chan.DSO. 9″ easy to read display. RS-232, GPIB, Parallel interfaces are available |
341 |
HP |
54602B |
150MHz, 20MS/s, 2 Chan. DSO. 9″ easy to read display. RS-232, GPIB, Parallel interfaces are available |
342 |
HP |
54721A |
1GHz Vertical amplifier plug-in. For 54700 series oscilloscopes |
343 |
HP |
1340A |
XY display. Z axis input. High speed and high resolution display.. |
344 |
HP |
37461A |
GPIB programmable display. 6″ Hi-res CRT. . |
345 |
HP |
54701A |
2.5GHz Active probe with complete set of accesories. Available w/o accesories option |
346 |
HP |
6281A |
0-7.5V, 0-5A, Constant current or voltage mode. Add PC interface for option (GPIB) |
347 |
HP |
6282A |
0-10V, 0-10A Const voltage or Current mode. Add PC interface for option (GPIB) |
348 |
HP |
6111A |
0-20V, 0-1A. 5 decades of resolution permit setting output voltage with 1mV accuracy |
349 |
HP |
6286A |
0-20 VDC, 0-10A, Voltage Regulation 0.01%. Add PC interface for option (GPIB). Simulate 120Wt solar panel output for inverter testing |
350 |
HP |
6264B |
0-20 VDC, 0-20A, Voltage Regulation 0.01%. Add PC interface for option (GPIB) Simulate 220Wt solar panel output for inverter testing. (GPIB interface with HP59501A) |
351 |
HP |
6284A |
0-20V, 0-3A Constant current or voltage mode. Add PC interface for option (GPIB) |
352 |
HP |
6552A |
0-20V, 0-25A New surpus units. Free rack mount kit. Simulate 500Wt solar panel output for inverter testing. Free GPIB interface |
353 |
HP |
6033A |
0-20V, 0-30A. Autoranging, 240Wt max. GPIB interface. |
354 |
HP |
6261B |
0-20V, 0-50A, Linear, Const. voltage or current. 115VAC (opt 26), 10 turn V/A pots (opt 9). GPIB interface with HP59501A |
355 |
HP |
6215A |
0-25V, 0-400 mA. Const voltage mode. 1mV ripple, size: 5.25×3.25×8″ Fine V adj. |
356 |
HP |
6334B |
0-36V, 0-10A, Constant current or voltage, Only 3″ high. Volt and amp meter |
357 |
HP |
6104A |
0-40V @1A or 2A from 0 to 20V. Precision power supply. Line regulation: 0.0005%+40uV, Load regulation: 0.0005%+100uV, Drift: 0.005%+50uV |
358 |
HP |
6200B |
0-40 V, 0-0.75A, or 0-20V at 0-1.5A. Constant voltage or current. Regulation: 0.01%. |
359 |
HP |
6266B |
0-40 V, 0-5A, Constant voltage or current. Regulation: 0.01%. Add PC interface for option (GPIB) |
360 |
HP |
6268B |
0-40V, 0-30A, Constant voltage/constant current mode. Regulation 0.01%. opt 26 & 28 avail. (GPIB interface with HP59501A) |
361 |
HP |
6012A |
0-60V, 0-50A, 1000Wt. 90day warranty. |
362 |
HP |
6206B |
0-60V @ 0.5A or 0-30 @ 1A dual range. 0.01% regulation, 200uV rms ripple |
363 |
HP |
6217B |
0-60V, 0-250mA. Const voltage mod.. Very small; 5.25″x3.25″x8″. Fine voltage adj. controls |
364 |
HP |
6218A |
0-60V, 0-250mA. Const voltage or current modes. Very small; 5.25″x3.25″x8″. |
365 |
HP |
6294A |
0-60V, 0-1A Constant current or constant voltage mode. 0.01% regulation. Linear. |
366 |
HP |
6296A |
0-60V, 0-3A Constant current or constant voltage mode. 0.01% regulation. Linear. |
367 |
HP |
6034L |
0-60V, 0-10A, 200Watt max., Computer programmable (GPIB) |
368 |
HP |
6274B |
0-60V, 0-15A, Const voltage or Current mode. Analog remote programming. Latest serial number |
369 |
HP |
6116A |
0-100V, 0.2A Precision voltage setting with 0.1%+1mV accy, 200uV resolution. |
370 |
HP |
6115A |
0-100V, 0.8A max Output voltage control with 4 digit accuracy. |
371 |
HP |
6035A |
0-500V, 0-5A, 1000Wt, Constant voltage or current. GPIB interface. |
372 |
HP |
6621A |
Two outputs 0-20VDC@ 0-2A or 0-7V @ 0-10A, GPIB interface |
373 |
HP |
6227B |
0-25V @ 0-2A. Dual output, CV/CC,Tracking mode. Low noise, single output winding produces continuous voltage up to 50V! |
374 |
HP |
6234A |
0-25V @ 0.2A dual or 0-50V single @ 0.2A. Small size: 3.64″x6.17″x8.25″. |
375 |
HP |
6253A |
0-20 @ 0-3A ea., 0.01% regulation, 200uV rms ripple. Constant voltage or current mode. Double output rating |
376 |
HP |
6255A |
0-40 @ 0-1.5A ea. 0.01% regulation, 200uV rms ripple. Const. voltage or current modes. Double output rating. Single output winding produces continuous voltage. NOTE: All inexpensive offshore P/S makers use two transformer windings to achive 40V output, hence they cannot produce linear continuous output. |
377 |
HP |
6237B |
0-18V @ 1A and two 0-20V outputs at 0.5A each. Tracking mode. |
378 |
HP |
4141B |
Programmable DC source/monitor for use in HP4062 semiconductor analysis systems |
379 |
HP |
6177B |
DC current source 0 to 500mA, 0-50V. 500uA resolution, 5mA, 50mA, 500mA range. |
380 |
HP |
6186B |
0 to 100mA, 0-300V. 3 ranges; 1mA, 10mA, 100mA |
381 |
HP |
J2301B |
Protocol analyzer opt 220, 220, 221. DS-3/E3 and Relay,ISDN,X.25,HDLC,SDL. RS232, RS449 & more. |
382 |
HP |
28687A |
Wiring Tester. Test any wiring harness for continuity and signal integrity (attenuation, crosstalk, burst). Tests 24 pairs simultaneously. Loopback adapters included. |
383 |
HP |
3779D |
Primary Multiplexer Analyzer for Bell/CCITT/Japanese networks |
384 |
HP |
37701B |
T1 Datcomm tester. ASYNC, SYNC, BERT. Ligthweight, Battery option available |
385 |
HP |
E4200B |
Broadband Test System modules; PDH, Line Interface Modules, Cell processors |
386 |
HP |
E4480A |
SONET Test Set. STS-1, STS-3, STS-3c, DS3.. |
387 |
HP |
E4480A |
SONET Test Set. opt: STS-1, DS3, DS1, DS0, Jitter for STS1,DS1,DS3. |
388 |
HP |
E4480A |
SONET Test Set. opt: ST1, STS-3, STS-3C, DS0, DS1, DS3, V1.5, FT1, Jitter: STS1, DS3, DS1, DS3 Pulse
Mask. |
389 |
HP |
E4480A |
SONET Test Set. opt: ST1, STS-3, STS-3C, STS-12, DS3, DS3 Pulse mask, V1.5, E1, DS0, DS1, TS, FM1, ATM, GPIB |
390 |
HP |
156MTS |
SONET Test Set. STS-1, STS-3, STS-3c, DS3. |
391 |
HP |
156MTS |
SONET Test Set. opt: STS-1, DS3, DS1, DS0, Jitter for STS1,DS1,DS3. |
392 |
HP |
156MTS |
SONET Test Set. opt: ST1, STS-3, STS-3C, DS0, DS1, DS3, V1.5, FT1, Jitter: STS1, DS3, DS1, DS3 Pulse
Mask. |
393 |
HP |
156MTS |
SONET Test Set. opt: ST1, STS-3, STS-3C, STS-12, DS3, DS3 Pulse mask, V1.5, E1, DS0, DS1, TS, FM1, ATM, GPIB |
394 |
HP |
3784A |
Digital communication analyzer. With Option 002. |
395 |
HP |
4934A |
Transmission Impairment and Noise Measurment test set available with opt 001 Rechargable batt or RS-232 interface |
396 |
HP |
4944A |
Transmission Impairment and Noise Measurment test set ( TIMS). |
397 |
HP |
4945A |
Transmission Impairment and Noise Measurment test set ( TIMS). 110kHz max freq. |
398 |
HP |
4951C |
Portable protocol analyzer 19.2 kbps max. Floppy disk to store setups and data. Supports HDLC, SDLC, SNA, ISDN, CCITT X.25, Async/Sync/Bysync, IPARS, DDCMP. |
399 |
HP |
4952A |
Portable protocol analyzer 64 kbps max. Floppy Drive. Supports HDLC, SDLC, SNA, ISDN, CCITT X.25, Async/Sync/Bysync, IPARS, DDCMP. Option 002 is available. |
400 |
HP |
18135A |
RS-232C Interface pod with Analyzer and DUT “Y” cable for HP4954A and other models |
401 |
HP |
18136A |
RS-449 Interface pod with Analyzer and DUT “Y” cable for HP4954A and other models |
402 |
HP |
18160A |
V-35 interface pod for HP 4951A/B/C, HP4952A and 4957A |
403 |
HP |
18173A |
RS-232C interface pod for HP 4951A/B/C, HP4952A and 4957A |
404 |
HP |
18179A |
RS-232C interface pod for HP 4951A/B/C, HP4952A and 4957A |
405 |
HP |
18180A |
RS-449 and RS232C interface pod for HP 4951A/B/C , HP4952A and HP4957A |
406 |
Hughes |
1077H11 |
TWT Amplifier 18 to 26.5 GHz, 1 Watt output. Full specs are available. |
407 |
Hughes |
8000H |
TWT Amplifier 3-5 GHz, 20 Watt output. Fulls specs are available upon request. |
408 |
Hughes |
8000H |
TWT Amplifier 10-15GHz, 40 Watt output. Fulls specs are available upon request. |
409 |
IFR |
A7550 |
Portable spectrum analyzer. 10kHz-1GHz coverage, Tracking generator. 70dB dynamic range. Monitor any type of FM/AM signals |
410 |
IFR |
A-7550 |
Portable spectrum analyzer. 10kHz-1GHz coverage, Tracking generator. 70dB dynamic range. Monitor any type of FM/AM signals |
411 |
Impulse Semi |
TLP |
Transmission Line Pulse Test System. Accurately measure ESD parameters for wafers or packaged devices. |
412 |
INCLUDED. |
|
|
413 |
Instek |
GDM-8040 |
DMM, Benchtop, Frequency, Capacitance, Max/Min, Relative, Temperature, 20A AC/DC current |
414 |
Instek |
GDS-2204 |
200MHz, 4 channel 1GS/s, 25K Samples memory. USB, Color LCD, RS-232, X-Y mode. |
415 |
Interface Technology |
RS-690 |
250MHz digital word generator. 64 channels, up to 16kB of data per chan. Min pulse width 4nS. Options included: Floppy disk, ECL pods, Variable current data pod (50Ohm) |
416 |
ISCO |
494 |
0-2000V, 0-200mA ( 100mA @ 2000V )Constant voltage, current or power mode Electrophoresis power supply |
417 |
JFW |
50DR-46-SMA |
Manual variable step attenuator. 50dB in 1dB steps. DC-2GHz, 2Wt, SMA connectors. |
418 |
JVC |
TM-550U |
PAL/NTSC studio monitor. Three way power source 12VDC/120VAC or 12V batt. small size. |
419 |
Kalmus |
166AP |
Pulse amplifier. 400-450MHz, 300Wt output power. Linear gain. |
420 |
Keithley |
175 |
4.5 digit DMM V/A/Ohms, 4.5 digit resolution, dB, Relative, Logging, Auto/Man |
421 |
Keithley |
175 |
DMM with GPIB interface. V/A/Ohms, 4.5 digit resolution, dB, Relative, Logging, Auto/Man |
422 |
Keithley |
197 |
Microvolt meter dB, Relative, Logging, Auto/Man, GPIB |
423 |
Keithley |
175 |
DMM with GPIB interface. V/A/Ohms, 4.5 digit resolution, dB, Relative, Logging, Auto/Man |
424 |
Keithley |
610B |
Electrometer with proportional analog output. Input Resistance >10E14 Ohms |
425 |
Keithley |
1992 |
Scanner card for Keithley 199 DMM |
426 |
Keithley |
2000 |
DMM/Scanner 6.5 digit resolution, 2000 reading/s (4.5 digit), GPIB, RS-232 |
427 |
Keithley |
619 |
Electrometer/DMM 5.5digit resolution, GPIB interface 6193 and 6194 input module. 10fA-2A, 10mOhm-2TOhm, 1uV-200V. 2nd channel 6 module available option |
428 |
Keithley |
AIM7 |
T/C Interface board for the Keithley 575 system |
429 |
Keithley |
706 |
Scanner/Switch unit. 10 slot for Keithley 7000 series control cards. |
430 |
Keithley |
7001 |
Scanner/Switch unit. 2 slot for Keithley 7000 series control cards. |
431 |
Keithley |
7011C |
Multiplexer card for the Keithley 7001, 7002 switch control unit. ii. |
432 |
Keithley |
7052 |
Relay matrix card 4×5 form factor. For Keithley 700, 7000 series mainframes |
433 |
Keithley |
7054 |
High voltage Relay matrix. For Keithley 705, 706 mainframes |
434 |
Keithley |
7055 |
Relay matrix card for Keithley 705, 706 mainframes |
435 |
Keithley |
7062 |
RF Relay switching card. For Keithley 705, 706 mainframes |
436 |
Keithley |
7071-4 |
Switching matrix card for Keithley 707. Dual 4×12 matrix with 5MHz BW. |
437 |
Keithley |
7072 |
Matrix card for 707 chassi.. Best Price |
438 |
Kenwood |
PD35-20D |
0-35V, 0-20A Digital displays, constant current or voltage modes. Linear design with extremely quiet output. |
439 |
Kenwood |
PWR18-1T |
2 of 0-18V @ 1A and 0-6V @ 5A. Tracking mode, 3 setup memory, output off control |
440 |
Kepco |
BOP20-5D |
Power amplifier Bipolar power supply. +/-20V, +/-5A. Works as a power op amp to driver loads up to 210Wt. |
441 |
Kepco |
BOP20-50MG |
Power amplifier Bipolar power supply. +/-20V, +/-50A. |
442 |
Kepco |
BOP36-6M |
Power amplifier Bipolar power supply. +/-36V, +/-6A. Works as a power op amp to driver loads up to 210Wt. |
443 |
Kepco |
ATE15-3 |
0-15V, 0-3A Constant current or voltage mode. Remote programming. Fast response Add GPIB interface for option |
444 |
Kepco |
JQE75-8M |
0 to 75V, 0 to 8A, Constant voltage or current mode. High resolution V/I control. |
445 |
Kepco |
ABC-200 |
0-200V, 0-150mA. 6.3VAC, Grid control output. CV or CC mode |
446 |
Kepco |
HB4A |
0-325V, in 5 ranges. 400mA. Constant voltage mode only. |
447 |
Kepco |
BOP1000M |
0 to +/-1000V, 40mA Bipolar DC Power supply and AC amplifier. Add GPIB interface with HP59501A |
448 |
Kikusui |
PLZ300W |
Electronic load. 300Wt max. Static or Dynamic mode. Constant current or resistance. |
449 |
Kikusui |
PAD8-5L |
0-8V, 0-5A, Constant current or voltage mode. Small size. Linear design |
450 |
Kikusui |
PAD35-5 |
0-35V, 0-5A Compact size, Remote control. Master/slave mode with tracking. add GPIB option |
451 |
Kikusui |
PAB110-0.6 |
0-110V, 0-0.6A. CV or CC mode. LCD readouts. Analog programming. 00-0010 |
452 |
Kikusui |
PAD160-7L |
0-160V, 0-7A. Constant duty power supply. CV or CC mode. Digital amp meter |
453 |
Kikusui |
PAB250-0.25 |
0-250V, 0-250mA. CV or CC mode. LCD readout. Analog signal remote programming |
454 |
Kikusui |
PAB350-0.1 |
0-350V, 0-1000mA. CV or CC mode. LCD readout. Analog signal remote programming |
455 |
Lambda |
UP6-33 |
0-6VDC, 0-33A, Programmable power supply. RS-232/485 interface. Compact high efficiency design. |
456 |
Lambda |
LT801-V1 |
5-12V, 0-100A Adjustable power supply. Const. Voltage or Current modes, Digital display, very compact and light weight. Line voltage: 208-260 VAC |
457 |
Lambda |
LLS4018 |
0-18V, 0-2A, Const current or voltage mode, digital controls & displays. |
458 |
Lambda |
LLS6018 |
0-18V, 0-9A, Const current or voltage mode, digital controls & displays. Small size Simulate solar panel |
459 |
Lambda |
LGSF24 |
24V, 41Amp, LED readout for V & A. Model # LGS-F-24-0V-R |
460 |
Lambda |
LP-412A-FM |
0-40V, 0-1A lab power supply, constant current or constant voltage mode, Separate meters for V and A. Low noise and low ripple. |
461 |
Lambda |
LP-522FM |
0-40V, 0-2A lab power supply, constant current or constant voltage modes, Analog meters for V and A. Small size. Low noise and low ripple. Cosmetically imperfect. |
462 |
Lambda |
LP-532FM |
0-40V, 0-3A lab power supply, constant current or constant voltage modes, analog meters for V and A. Low noise and low ripple. Line regulation: 0.01% |
463 |
Lambda |
LQ-532 |
0-40V, 0-5A. Digital display. Constant current or constant voltage mode. Remote control capability |
464 |
Lambda |
LQ-523 |
0-60 V, 0-900 mA, digital V/A display, CV/CC mode, small size. Remote analog programming. |
465 |
Lambda |
LQ-533 |
0-60V, 0-3.3A. Digital display. Constant current or constant voltage mode. 0.01% regulation. |
466 |
Lambda |
LPT-7202FM |
2 of 0-20V @ 1.5A each and 0-7V @ 5A. Separate volt and amp meters for each output. |
467 |
Leader |
LMV-181A |
AC Millivoltmeter. 100uV-300V sensitivity, 5Hz-1MHz, dBV, dBM, V scales.. |
468 |
Leader |
LDM-170 |
Distortion/SINAD Meter with Voltmeter function. 1mV-300V input, 20Hz-20kHz. Filtering function |
469 |
Leader |
LCG-399 |
PAL Video Signal Generator. Selectable audio modulation formats, Composite video, Full channel coverage.. iii |
470 |
Leader |
LCG-400 |
Video Signal Generator NTSC. Sound, Variable Sync option, Gen-Lock, Optional Multiburst module, TV modulator |
471 |
Leader |
LCG-409 |
Video Signal Generator NTSC. Composite & Channels 2 to 86, Sound, RGB, Battery/AC pwr. |
472 |
Leader |
LBO-5860L |
TV waveform monitor. Dual channel, Line selection, field selection functions. |
473 |
Leader |
LVS-5851A |
PAL/NTSC Vectroscope. Dual channel.. |
474 |
Leader |
LTC-905B |
Semiconductor curve tracer. Test BJT’s, MOSFET’s, UJT’s, Diode’s, SCR’s on any oscilloscope! |
475 |
Leader |
LPS-152 |
2 of 0-25V @ 1A and 0-6V @ 5A. Tracking mode. <3mV p-pk ripple |
476 |
LeCroy |
9211 |
Pulse generator plug-in. 250MHz repetition rate.. 300pS rise time, 5V into 50Ohm. |
477 |
LeCroy |
9214 |
Pulse generator plug-in. 300MHz repetition rate. 300pS rise time, 5V into 50Ohm. |
478 |
LeCroy |
LW420 |
Programmable Arbitrary Waveform Gen. 100MHz, 400Ms/s, dual channel, 1MB memory |
479 |
LeCroy |
9310L |
300MHz, 2CH, with 1MB points memory per channel option (“L”). GPIB, RS-232, PCMCIA, 9″ display |
480 |
LeCroy |
9354AM |
500MHz, 2CH, with 1MB points memory. GPIB, RS-232, PCMCIA, 9″ display |
481 |
LeCroy |
9361C |
300MHz, 2.5GS/s, 2 Chan, 25kSamples mem., 9″ display, FDD, GPIB, RS232, Centronics ports. |
482 |
LeCroy |
9362C |
1.5GHz, 10GS/s, 2 Channel, 9″ display, FDD, GPIB, RS232, Centronics ports. |
483 |
LeCroy |
PP006 |
500MHz, 10MOhm, General purpose oscillscope probe. Can be used with any scope. New! |
484 |
LeCroy |
D300 |
4GHz Differential probe for use with Lecroy 9000 series oscilloscopes |
485 |
LG |
OS-9020A |
20MHz, 2 Channel, easy to use full featured oscilloscope. |
486 |
LG |
OS-9020G |
20MHz, 2 Channel with 1MHz Function generator. 10V p-pk output into 50Ohm, Sine, Triangular, Square waves. DC offset |
487 |
Link Instruments |
ADF25A |
High voltage differential probe. 20MHz, 1000V rms. Works with any oscilloscope. |
488 |
Mini-Circuits |
TIA-1000-4 |
Power amplifier 100MHz-1GHz, 19dB gain, 4Wt linear, 12.5Wt saturated. |
489 |
Mini-Circuits |
ZHL-32A-S |
Amplifier 0.05-130MHz, 25dB gain, +29dBm max. output, SMA, IP3: +38dBm Full specs |
490 |
Mini-Circuits |
ZHL-2-8-S |
Amplifier 10-1000MHz, 31dB min. gain, +29dBm max. output, SMA, IP3: +38dBm. Full specs |
491 |
Minolta |
TV-2130 |
Color and Luminance analyzer. Analyzer any color LCD or CRT for color purity and consistency. |
492 |
Minolta |
TV-2140 |
Color and Luminance analyzer. Analyzer any color LCD or CRT for color purity and consistency. |
493 |
Minolta |
TV-2150 |
Color and Luminance analyzer. Analyzer any color LCD or CRT for color purity and consistency. |
494 |
Narda |
4779-6 |
6dB Attenuator, DC-18GHz, SMA (m/f), 2Wt . QVI |
495 |
Netcom |
X-1000 |
Fast Ethernet tester/simulator/analyzer for IEEE802.3.ture |
496 |
Netcom |
JET-210 |
Jitter generator/standard for IEEE802.3 Ethernet standard |
497 |
Netcom |
JET-211 |
Jitter generator/standard for IEEE802.3 Ethernet standard |
498 |
Nettest |
742S |
GN Nettest 7500 plug-in. Combines a source and power meter in one module 1310-1550nm |
499 |
Nettest |
7500 |
OTDR. Flexible configuration with optional plug-in modules. |
500 |
Network Communications |
NP7100 |
Communication analyzer. T1, T1/2Mb, BERT, Digital TIMS, VOM, oscope, VT220 emulator, Tone generator.. Interfaces: RS232 V.24, RS-422, V35, T1, Telco, ISDN |
501 |
NI |
BNC-2080 |
BNC interface board. p/n 181630 |
502 |
NI |
GPIB-TNT |
National Instruments GPIB board for a PC. 16 bit. For any PC with ISA slot |
503 |
NI |
182009-04 |
GPIB interface cable, standard to Single-End Male. p/n 182009-04 X5 Double-Shielded, 4 meter |
504 |
NI |
776857 |
GPIB interface with PCMCIA card. New in a box! National Instruments. |
505 |
NI |
GPIB-PCMCIA |
GPIB interface with PCMCIA card. New in a box! National Instruments p/n 776857 |
506 |
NI |
SB-GPIB-TNT |
National Instruments GPIB board for SB bus |
507 |
NI |
SCXI-1300 |
General-purpose terminal block with an onboard temperature sensor for cold-junction compensation. |
508 |
NI |
SCXI-1102B |
32 channel amplifier board. 200Hz BW. 333 kS/s maximum sampling rate |
509 |
NI |
SCXI-1163R |
32 channel opto-isolated solid state relay module |
510 |
NI |
SB-GPIB-TNT |
National Instruments GPIB board for SB bus |
511 |
NI |
VXI-MXI-2 |
National Instruments VXI CPU card. |
512 |
NI |
183105A-01 |
National Instruments VXI CPU card. |
513 |
NI |
182429H-20 |
National Instruments VXI CPU card.. VXIPC-486 model 566 |
514 |
NI |
777145-01 |
National Instruments I/O connector block. New in a box!. |
515 |
NI |
763061-03 |
National Instruments 4.1m GPIB cable |
516 |
NI |
763507-02 |
National Instruments 2.0m GPIB cable |
517 |
NI |
763061-02 |
National Instruments 2.1m GPIB cable |
518 |
NI |
763061-4 |
National Instruments 8m GPIB cable |
519 |
Noisecom |
NC9656 |
Programmable noise generator. 500MHz-9GHz, 0dBm max output, 80dB attenuator with 1 dB step resolution, GPIB interface, Filter function. |
520 |
NoiseCom |
UFX/BER IBS/IDR |
Noise generator capable of Carrier-to-noise (C/N), Carrier-to-noise density (C/No), Bit energy-to-noise density (Eb/No), Carrier-to-interferer (C/I), RF power and Precision noise generator. Optional Automatic Gain control (Tracking) |
521 |
NoiseKen |
FVC-777 |
EMI Analyzer. Measure spectral density of Electromagnetic fields from 100kHz to 1GHz.. Complete system! datasheet |
522 |
Philips |
PM5715 |
50MHz pulse generator. 10V output into 50 Ohm, adjustable transition times. |
523 |
Philips |
PM5418TD |
Video Signal Generator PAL/SECAM/NTSC, 15 Sound formats, Baseband or RF out.. |
524 |
Philips |
PM2813 |
3 of 60V @ 5A each, 60Wt maximum. Programmable, with GPIB interface. PM2813/113 |
525 |
PM |
1038-N10 |
Scalar Network Analyzer. Detectors and mainframe are available separately |
526 |
PM |
1038-D14M |
Scalar Network Analyzer chassi. Detectors and PM1038-N10 module are available separately |
527 |
Polar |
550 |
Milliohmmeter with short locator. Measure resistance down to 1 mOhm or locate short circuits on any PCB board., Built-in current source. Ohmmeter 200 mOhm to 20 kOhm in 4 ranges. |
528 |
Power Design |
TP325 |
2 of 0-32V @ 1A each and 0-6V @ 5A Tracking mode. This P/S will not cause IC lockup on power up. Specs iii |
529 |
Power Design |
TP340 |
2 of 0-32V @ 1A each and 0-6V @ 5A or 0-15V @ 2.5A Tracking mode. This P/S will not cause IC lockup on power up. Specs vii |
530 |
Power Design |
TP343A |
2 of 0-25V @ 2A each and 0-6V @ 5A or 0-15V @ 2.5A. Tracking mode. This P/S will not cause IC lockup on power up. Specs xiv |
531 |
Power Design |
TP343B |
2 of 0-20V @ 2A each and 0-6V @ 5A or 0-15V @ 2.5A Tracking mode. This P/S will not cause IC lockup on power up. Specs |
532 |
Power Desing |
TW5005W |
Dual 0-50V, 0-0.5A output with tracking function. Single range with no output voltage jumps |
533 |
Power Ten |
4600D-20125 |
0-20V, 0-125A, LCD displays, Const current or voltage mode. Line requirements: 190-253VAC sinlge or 3 phase |
534 |
Power Ten |
3300D-6010 |
0-60V, 0-10A, LCD displays, Height: 1.5″ Const current or voltage mode. |
535 |
Power Ten |
4600D-15033 |
0-150V, 0-33A, LCD displays, Const current or voltage mode. Line requirements: 190-253VAC single or 3 phase |
536 |
Prism |
PPS 50S-1 |
0-50V, 0-1A, Programmable power supply. GPIB interface. High resolutions (4 digit) |
537 |
Quantum Data |
801GX |
Video generator. PAL/NTSC, VGA, MAC, SUN, S-Video, RGB. 100 built in patterns, 300 custom patterns. GPIB, RS-232C. |
538 |
Quantum Data |
8701E |
285 MHz analog video generator. Supports all forms of EIA composite sync. With. ACV 285 unit |
539 |
R&S |
SMIQ02 |
2.2GHz Vector Signal Generator. -140 to +13dBm with 0.1dB step. SSB phase noise <-126 opt B19. |
540 |
Rohde & Schwartz |
CMT55 |
Radio Communication Analyzer with Optional GSM measurements mode. 0.1MHz-2000MHz, RF power, Frequency, Modulation, Modulation amplitude, SINAD, Oscilloscope, Transmitter or Receiver test mode.ture Options CMU-20, CMT-U26 |
541 |
Rohde Schwartz |
UPSF |
Video noise meter. 40 MHz BW, High resolution, filter functions.. |
542 |
Rohde Schwartz |
UPSF2E2 |
UPSF2 noise meter measurement module. |
543 |
Schaffner |
NSG222 |
Interference generator. For use with Schaffner mainframe chassi only |
544 |
Sencore |
SCR250 |
SCR tester for use with LC102 analyzer. |
545 |
Sorensen |
XTS7-6M5 |
0-7V, 0-6A with Opt M5 analog programming interface. Const current or voltage mode, 3.5 digit digital displays |
546 |
Sorensen |
XHR7.5-130 |
0-7.5V, 0-130A, with opt M9B (RS-232C), Constant current or voltage mode. High efficiency, small footprint. |
547 |
Sorensen |
XTS15-4 |
0-15V, 0-4A Constant current or voltage mode. With opt GPIB-M |
548 |
Sorensen |
HPD15-20S |
0-15V, 0-20A Constant current or voltage mode. Digital display with analog bargraph. |
549 |
Sorensen |
DCS20-150 |
0-20V, 0-150A, Constant current or voltage mode. High efficiency. Line requirements: Single or 3 phase 190-240VAC. a001 |
550 |
Sorensen |
DCS33-33E |
0-33V, 0-33A, opt M9; GPIB/RS232.. v |
551 |
Sorensen |
DCS50-40M16 |
0-50V, 0-40A, 1 or 3 phase AC input, current monitor output. |
552 |
Sorensen |
XTS60-1 |
0-60V, 0-1A Constant current or voltage mode. Digital display with analog bargraph |
553 |
Sorensen |
QRD60-1.5 |
0-60V, 0-1.5A Constant current or voltage mode. |
554 |
Sorensen |
XTS60-1 |
0-60V, 0-1A Dual output. Constant current or voltage mode. Digital display with analog bargraph. |
555 |
Sorensen |
DCS60-18 |
0-60V, 0-18A, Const voltage or Current mode. Only 1.5″ tall, rackmount standard. |
556 |
Sorensen |
DHP100-50M9D |
0-100V, 0-50A. option M9D (GPIB interface). Line requirements: 200-240VAC, 3 Phase |
557 |
Sorensen |
DHP130-115 |
0-130V, 0-115A. Line requirements: 200-240VAC, 3 Phase |
558 |
Sorensen |
DCS150-7E |
0-150V, 7A, Constant current or voltage mode. High efficiency, rack mountable, only 1.5″ in height. GPIB interface is available |
559 |
Sorensen |
DCR150-3B |
0-150V, 0-3A, Constant current or voltage mode. |
560 |
Sorensen |
DCR150-18B |
0-150V, 0-18A, Constant current or voltage mode. Line voltage: 115VAC |
561 |
Sorensen |
XT250-0.25 |
0-250V, 0-250mA. Constant voltage or current mode. 3 1/2 digit digital meters |
562 |
Sorensen |
LT18-5 |
2 of 0-18V @ 5A each, 5V @ 3A. 18V outputs can be used in series to double the voltage to 36V, or in parallel to get 10A. |
563 |
Spectracom |
8160a |
Standard Frequency receiver with 10 MHz output. |
564 |
Spirent |
AX/4000 |
10GB Ethernet test system. Incl. 16slot chassi, 401427 control module, 403100 Generator/Analyzer, 403335 Test interface |
565 |
Spirent |
403100 |
10GB Ethernet test system. 403100 Generator/Analyzer, 403335 Test interface |
566 |
Spirent |
403335 |
10GB Ethernet test system. 403100 Generator/Analyzer, 403335 Test interface |
567 |
Spirent |
DLS200 |
Wireline simulator for DSL and ISDN with Impairment generator option. 10 standard test loops plus crosstalk, impulse, powerline and longitudal noise impairments |
568 |
Spirent |
SMB-1000 |
Network tester mainframe. We have wide variety of plug-in cards for this tester |
569 |
Spirent |
SMB-2000 |
Network tester mainframe. We have wide variety of plug-in cards for this tester |
570 |
Spirent |
SMB1000 |
Network tester mainframe. We have wide variety of plug-in cards for this tester |
571 |
Spirent |
SMB2000 |
Network tester mainframe. We have wide variety of plug-in cards for this tester |
572 |
Spirent |
SE-6205 |
Interface card for Smartbits 1000 and 2000 systems. Quantity discount. |
573 |
Spirent |
ST-6405 |
Interface card for Smartbits 1000 and 2000 systems. Quantity discount. |
574 |
Spirent |
SX-7205 |
Interface card for Smartbits 1000 and 2000 systems. Quantity discount. |
575 |
Spirent |
SX-7405 |
Interface card for Smartbits 1000 and 2000 systems. Quantity discount. |
576 |
Spirent |
XPS/26-R24 |
Programmable Transmission Line simutaltor. Up to 15500 feet, GPIB interface. Rev. 6 |
577 |
SRS |
DG535 |
Repair service for your Stanford Research Systems DG535 Digital delay generator. |
578 |
SRS |
DG535 |
Digital delay pulse generator. Opt 001. |
579 |
SRS |
SR245 |
Computer Interface for NIM chassi.! |
580 |
SRS |
SR250 |
Intergator Box Car Averager for the NIM chassi.! II |
581 |
SRS |
SR280 |
Power supply and Display module for SRS NIM chassi. |
582 |
Stanford Research |
DS335 |
3.1MHz Synthesized Sweep-Function generator. GPIB & RS232. 1uHz resolution, 10 Vpp into 50Ohm |
583 |
Stanford Research |
DS345 |
30MHz Synthesized Function/Arbitrary/ /Sweep generator. GPIB (opt 001). 1 µHz to 30.2 MHz, 1 µHz resolution. Sine, square, ramp, triangle and noise, AM/FM/Burst/Phase. Info |
584 |
Sunrise Telco |
Sunset xDSL |
Portable Test Set. With opt. AD7: TDR/Line/DVM, AA0, SSXDSL-4: Alcatel ADSL ATU-C module |
585 |
Systron Donner |
TL8-3 |
2 of 0-32 @ 1A each, 0-8V @ 3A. Separate meters for each output. |
586 |
T-Com |
324A |
T1 hand-held tester. Built in generator with BERT functions. Non intrusive DS1 monitoring and HDSL testing. |
587 |
TEK |
TDS784D |
1GHz, 4 Chan., 4GS/s. Options: 13,1F, HD, 2M, 2F |
588 |
TEK |
577/D2 |
Curve tracer 100Wt, 10A continuous, 20A peak pulse current power. Test any semiconductor device for V-I characteristics. Also test batteries, lamps, relays. With 177 test fixture. Device adapters are available. |
589 |
TEK |
576 |
Tektronix 576 Curve tracer Flat Rate Repair Service. |
590 |
TEK |
5A14N |
4 Channel Vertical amplifier plug-in for the Tektronix 5000 series oscilloscopes. |
591 |
Tektronix |
TLA7M2 |
68Ch, 2GHz timing, 100MHz state analyzer module for TLA 700 series analyzers |
592 |
Tektronix |
TLA704 |
Logic analyzer system. Boards are available separately. |
593 |
Tektronix |
1241C |
Test probes and ROM packs only |
594 |
Tektronix |
VX4820 |
Digital Test Module for testing TTL systems. 64 channel. C-size, VXM bus module. ii |
595 |
Tektronix |
VM700A |
Vidio signal analyzer Options 1, 11, 40. |
596 |
Tektronix |
VM700T |
Vidio signal analyzer Options 1, 11. |
597 |
Tektronix |
DAS9200SE |
Digital analysis system. Boards are available separately.. |
598 |
Tektronix |
RFM151 |
CATV signal analyzer. Complete signal measurements from 5MHz-1080MHz. RS-232 interface. |
599 |
Tektronix |
TFS3031 |
OTDR. Single Mode Optical Time Domain Reflectometer. 1310 nm & 1550 nm single mode version. Unused, with optional printer, FDD (opt 11), opt 8, Carrying case, New battery, Transit case |
600 |
Tektronix |
DC504A |
100Mz Universal Counter Timer. Measure Freq., Period, Time, Events & more. For TM chassis |
601 |
TEKTRONIX |
DC509A |
135 MHz, Dual channel Universal Counter/Timer. 8 digit Display, 5 ps max resolution, Auto trigger, Probe compensation, A and B outputs, high stability Oven Time Base (opt 1). Works in TM 500/5000 chassis |
602 |
Tektronix |
DC5010 |
350Mz Universal Counter Measure Freq., Period, Time, Events, GPIB interface. For TM500X |
603 |
Tektronix |
DM502A |
DMM with RTD Thermometer option. Requires TM 500/5000 series chassi |
604 |
Tektronix |
AWG2020 |
250MS/s arbitrary waveform generator. Digital outputs (opt 003), FFT editor (opt 009) |
605 |
Tektronix |
AWG2040 |
500MHz arbitrary waveform generator opt 1,3,9. 4MB record length (opt 001), Digital outputs (opt 003),
FFT editor (opt 009) |
606 |
Tektronix |
DG2020A |
Progrmmable Data generator. 200MHz data rate, 64k word memory. Simulates LCD and CCD signals |
607 |
Tektronix |
DG2020A |
Progrmmable Data generator with TEK P3420 pod. 200MHz data rate, 64K word pattern memory |
608 |
Tektronix |
PG501 |
50 MHz Pulse generator. <20nS to 200mS period, <10nS to 100mS pulse duration . +/-5V output into 50 ohms, Square wave mode, <3nS Rise time, Ext. trigger In/Out Dual adjustable complim. outputs. |
609 |
Tektronix |
PG502 |
10Hz-250MHz Pulse generator, 1nS rise time, +/-5V output (5V p-pk max). Single pulse mode. |
610 |
Tektronix |
PG505 |
High voltage pulse generator. 1MHz repetition rate. 80V pk-pk into 4kOhm, Variable Transition times. |
611 |
Tektronix |
TG501 |
Time mark generator for calibrating any oscilloscope time base. Optional 5MHz time base. |
612 |
TEKTRONIX |
SG502 |
Oscillator, 5Hz to 500kHz Sine and Square Waves, Low distortion Sine Wave, 5 V RMS, 600Ohm output impedance, 70dB attenuator with 10dB steps. |
613 |
Tektronix |
SG503 |
250 MHz leveled sinewave generator with Freq. counter. Requires TM 500 chassi. Newer s/n |
614 |
|
SG504 |
1024 MHz sinewave generator w/o output head. Requires TM 500 chassi. |
615 |
Tektronix |
AGL1 |
Analog Generator Lock module for TG2000 mainframe. |
616 |
Tektronix |
AVG1 |
Analog Multiformat generator module for Tektronix TG2000 mainframe. |
617 |
Tektronix |
BG1 |
Black Generator module for Tektronix TG2000. |
618 |
Tektronix |
DVG1 |
Digital Generator module for Tektronix TG2000. |
619 |
Tektronix |
TSG130 |
Miltiformat video test signal generator with audio outputs. NTSC format. |
620 |
Tektronix |
TSG131A |
Miltiformat video test generator with audio outputs.Option 003. PAL format. |
621 |
Tektronix |
TSG170 |
Video test generator. 15 test patterns. Digital genlock. NTSC format. |
622 |
Tektronix |
TSG 170 |
Video test generator. 15 test patterns. Digital genlock. NTSC format. |
623 |
Tektronix |
TSG601 |
Video generator for serial digital format. Audio channels. Built in 50m coax cable simulator. Handheld size. Soft case included |
624 |
Tektronix |
1410 |
Video test generator with SPG2, TSG7, TSP1, TSG3, TSG5, TSG6 . |
625 |
Tektronix |
1411 |
Video test generator with SPG12, TSG11, TSP11, TSG13, TSG15, TSG16. |
626 |
Tektronix |
1910 |
Video test generator/ Inserter. Studio, transmitter abd transmission test signals. 10-Bit signal generation. Opt 1 avail. |
627 |
Tektronix |
VITS 100 |
Video test generator/ Inserter. NTC 7, FCC, and VIR Signals. FCC composite, multiburst |
628 |
Tektronix |
VITS100 |
Video test generator/ Inserter. NTC 7, FCC, and VIR Signals. FCC composite, multiburst |
629 |
Tektronix |
VITS 200 |
Generator/Inserter NTC7, FCC, VIRS, and GCR Signals Cable Multiburst and Sweep Signals. |
630 |
Tektronix |
VITS200 |
Generator/Inserter NTC7, FCC, VIRS, and GCR Signals Cable Multiburst and Sweep Signals. |
631 |
Tektronix |
DBI200 |
VBI Data Broadcasting Insertion System. All the features of VITS200 with addition of a computer interface. New in a box |
632 |
TEKTRONIX |
AM502 |
Differential amplifier with Hi/Lo pass filter.Gain from 1 to x100,000 in 5 decades. 1MHz BW, CMRR 100dB. |
633 |
Tektronix |
SI5010 |
Programmable scanner for the TEK TM5000 series chassis. 16 channels. BNC connector |
634 |
Tektronix |
7D20 |
Digitaizer plug-in.Digital storage oscilloscope plug in for the TEK 7000 series oscilloscopes |
635 |
Tektronix |
DSA602A |
Digital signal analyzer/DSO. 1GHz BW, 2Gs/s up to 12 input channels. Plug-ins available |
636 |
Tektronix |
RTD710 |
Waveform digitizer. 200MS/s, 10 bit resolution. Works with any X-Y display.! |
637 |
Tektronix |
RTD720 |
Waveform digitizer. 2GS/s, optional 1MB memory (opt 11).! |
638 |
Tektronix |
TWD 120 |
Color Digital Storage oscilloscope on any PC. 100 Megasaples/sec. 8 bit vertical resolution. 5000 points record per channel. Smaller than a laptop. Windows 3.1/95/98 software, Carrying case, Manual, SCSI card and cable. t1, Pic2 Demo download |
639 |
Tektronix |
222 |
Handheld 10MHz, 2 Chan. Digital storage, 10Ms/s, Battery or 12VDC operation. |
640 |
Tektronix |
TDS320 |
100MHz, 2 Chanel, 500MS/s, 2mV sensitivity. Measure 11 waveform parameters automatically. |
641 |
Tektronix |
TDS340A |
100MHz, 2 Chan., 500MS/s, 2mV sensitivity. GPIB, RS-232, VGA, Floppy Drive and Printer port. |
642 |
Tektronix |
TDS350 |
200MHz, 2 Channel, 1GS/s, 2mV sensitivity. Measure 11 waveform parameters automatically. |
643 |
Tektronix |
TDS360 |
200MHz, 2 Channel, 1GS/s, 2mV sensitivity. Measure 11 waveform parameters. Floppy drive |
644 |
Tektronix |
TDS 360 |
200MHz, 2 Chan., 1GS/s, 2mV sensitivity. Measure 11 waveform parameters Floppy drive |
645 |
Tektronix |
TDS460 |
350MHz, 4 Channel, Options: 1F (floppy drive). Rackmount kit available.. |
646 |
Tektronix |
TDS460A |
400MHz, 4 Channel, Options: 1F (floppy drive). Rackmount kit available.. |
647 |
Tektronix |
TDS460A |
400MHz, 4 Channel, Options: 1M, 05, 2F, 13. Rackmount kit available .. |
648 |
Tektronix |
TDS460A |
400MHz, 4 Channel, Options: 1M, 05, 2F, 13. Optional portable printer (opt. TDS4F5P) |
649 |
Tektronix |
TDS460AXL |
400MHz, 4 Chan., Options: 1M (120K memory), 05 (Video), 2F (FFT & Waveform Math), 13 (GPIB, RS-232, Centronics). Rackmount kit available |
650 |
Tektronix |
TDS 460AXL |
400MHz, 4 Chan., Options: 1M (120K memory), 05 (Video), 2F (FFT & Waveform Math), 13 (GPIB, RS-232, Centronics). Rackmount kit available |
651 |
Tektronix |
TDS520C |
500MHz, 1GS/s, FFT (opt 2F), HD (160MB hard drive), FDD (opt 1F) |
652 |
Tektronix |
TDS520 |
REPAIR SERVICE |
653 |
Tektronix |
TDS524A |
REPAIR SERVICE |
654 |
Tektronix |
TDS540 |
500MHz, 1GS/s, 4 channel. Flexible triggering, 50K points record per channel (opt 1M), Opt 2F (FFT), opt 13 (RS-232, Parallel Inteface) |
655 |
Tektronix |
TDS510 |
REPAIR SERVICE |
656 |
Tektronix |
TDS510A |
REPAIR SERVICE |
657 |
Tektronix |
TDS520 |
REPAIR SERVICE |
658 |
Tektronix |
TDS520A |
REPAIR SERVICE |
659 |
Tektronix |
TDS520D |
REPAIR SERVICE |
660 |
Tektronix |
TDS540 |
REPAIR SERVICE |
661 |
Tektronix |
TDS540A |
REPAIR SERVICE |
662 |
Tektronix |
TDS540C |
REPAIR SERVICE |
663 |
Tektronix |
TDS540D |
REPAIR SERVICE |
664 |
Tektronix |
TDS544A |
REPAIR SERVICE |
665 |
Tektronix |
TDS640 |
REPAIR SERVICE |
666 |
Tektronix |
TDS640A |
REPAIR SERVICE |
667 |
Tektronix |
TDS644 |
REPAIR SERVICE |
668 |
Tektronix |
TDS644A |
REPAIR SERVICE |
669 |
Tektronix |
TDS744A |
REPAIR SERVICE |
670 |
Tektronix |
TDS754C |
REPAIR SERVICE |
671 |
Tektronix |
TDS784A |
REPAIR SERVICE |
672 |
Tektronix |
TDS784D |
REPAIR SERVICE |
673 |
Tektronix |
TLS216 |
REPAIR SERVICE |
674 |
Tektronix |
TDS820 |
REPAIR SERVICE |
675 |
Tektronix |
TDS210 |
60MHz, 2 Channel, 1GS/s, LCD display, automatic waveform measurements, math functions, X-Y mode |
676 |
Tektronix |
TDS784D |
1GHz, 4 Chan., 4GS/s. Options: 05,13,1F, HD, 2F, 2C |
677 |
|
2201 |
20MHz, 10MS/s, 2Ch, Digital storage and Analog scope in one instrument. 2mV to 5V per/div |
678 |
Tektronix |
2220 |
60MHz, 20MS/s, 2Ch, digital storage and analog scope in one instrument. 2mV to 5V per/div sensitivity. |
679 |
Tektronix |
2221 |
60MHz, 100MS/s, 2Ch, digital storage and analog scope in one instrument. 2mV to 5V per/div sensitivity. Optional GPIB port |
680 |
Tektronix |
11403A |
Oscilloscope mainframe. 3GHz Bandwith. Option 1S. Plug-ins are available separetely |
681 |
Tektronix |
TAS465 |
100MHz, 2 Channel, Automatic measurment of waveform parameters. 90 day warranty |
682 |
Tektronix |
TAS475 |
100MHz, 4 Chan, Automatic measurment of waveform parameters. 90 day warr. |
683 |
TEKTRONIX |
2213 |
60MHz portable oscilloscope. 2mV sensitivity,. Lightweight: 13 lb. 6month warr. |
684 |
TEKTRONIX |
2225 |
50 MHz, 2 Channel, 2mV max sensitivity, Dual time base.Weights only 13lb. |
685 |
Tektronix |
AN/USM-488 |
100MHz , 2Ch,. 2mV sensitivity, dual time base. TV triggering.. only 13lb, 6month warr. |
686 |
TEKTRONIX |
2235 |
100MHz , 2Chanel,. 2mV sensitivity, dual time base. TV triggering.. only 13lb, 6month warr. |
687 |
TEKTRONIX |
2235A |
100MHz , 2Channel,. 2mV sensitivity, dual time base. TV triggering.. only 13lb, 6month warr. |
688 |
TEKTRONIX |
2236 |
100MHz oscilloscope with Frequency Counter and 4.5 digit Digital multimeter. 6 month warranty |
689 |
TEKTRONIX |
2245A |
100MHz , 4Ch. 2mV sensitivity, dual time base. Cursor measurements. Automatic setup |
690 |
TEKTRONIX |
2247A |
100MHz , 4Ch. 2mV sensitivity, dual time base. Autosetp and automatically measurement of waveform parameters. |
691 |
Tektronix |
2445 |
150MHz, 4 channel. Dual time base. Portable, weight 22.4 lb. 90 day warranty |
692 |
TEKTRONIX |
2445B |
200MHz, 4 ch. with cursor measurements of V & time. Dual time base. Portable, weight 22.4 lb. 90 day warr. two 200MHz probes, GPIB and other options are available |
693 |
TEKTRONIX |
2465 |
300MHz, 4 channel. two 300MHz probes, 45 day warranty. Option 11 (active probe power supply) |
694 |
TEKTRONIX |
2465CTS |
300MHz 4 channel with Counter-Timer and GPIB IEEE-488 interface. 6 month warr. |
695 |
Tektronix |
2465A |
350MHz 4 channel analog oscilloscope. Autosetup, on screen waveform parameter measurements. |
696 |
Tektronix |
2465ADV |
350MHz 4 channel analog oscilloscope with DMM option |
697 |
Tektronix |
2465B |
REPAIR & CALIBRATION. ANY PROBLEM. Includes NIST traceable calibration |
698 |
Tektronix |
2465B |
400MHz 4 ch 500pS rise time. Auto setup feature, on-screen measurements of 12 waveform parameters. 90 day warranty, Different options are available |
699 |
Tektronix |
2465BDM |
400MHz 4 ch 500pS rise time. Auto setup feature, on-screen measurements of 12 waveform parameters. optional built in 4.5 digit DMM, Frequency Counter, GPIB interface. |
700 |
Tektronix |
2467B |
400MHz 4 channel. Autosetup & Automatic waveform measurements. GPIB interface. |
701 |
Tektronix |
5103N |
2MHz analog storage oscilloscope. |
702 |
Tektronix |
5111 |
2MHz analog storage oscilloscope. |
703 |
Tektronix |
5115 |
2MHz analog storage oscilloscope. Up to 8 traces simultaneously with 5A14 plug-ins. |
704 |
Tektronix |
5440 |
50 MHz analog oscilloscope. Up to 4 analog channels. Rack mount version is available |
705 |
TEKTRONIX |
7603 |
100MHz Modular oscilloscope. Up to 4 input channels. |
706 |
Tektronix |
7623A |
100MHz, Analog storage oscilloscope. Choose from many types of plug-ins. |
707 |
Tektronix |
7633 |
100MHz, Analog storage oscilloscope. Choose from many types of plug-ins. SOLD |
708 |
|
7834 |
400MHz, Analog storage oscilloscope. 4 input channels. |
709 |
Tektronix |
7104 |
1GHz Oscilloscope, the fastest, real-time oscilloscope ever made. Ultra-high writing speed of 20 cm/us. 350 ps rise time. Complete dual channel dual time base system |
710 |
Tektronix |
C-5C |
Oscilloscope camera. Capture single shot events with analog Tektronix oscilloscopes. |
711 |
Tektronix |
WFM300 |
TV Waveform Monitor. Betacam mode (opt. 10).. |
712 |
Tektronix |
WFM601E |
Video Waveform Monitor for 270MB serial component operating enviroment. |
713 |
Tektronix |
5CT1N |
Semiconductor curve tracer. Up to 0.5W. 10nA/div to 20mA/div, 0.5V/div to 20V/div horisontal factors. FET or Bipolar devices. |
714 |
Tektronix |
528A |
Waveform Monitor for NTSC |
715 |
Tektronix |
577/D1 |
Curve tracer 100Wt, 10A continuous, 20A peak pulse current power. Storage Mode. Test any semiconductor device for V-I characteristics. Also test batteries, lamps, relays. With 177 test fixture. Device adapters are available. |
716 |
Tektronix |
576 |
Semicunductor Curve tracer. 220Wt, 1500V. Device adapters are available. |
717 |
Tektronix |
067-0405-02 |
Calibration fixture for TEK TDS7000 series oscilloscopes |
718 |
Tektronix |
1420 |
NTSC Vectroscope with two separate input channels. Phase adjustment. Open frame chassi |
719 |
Tektronix |
1485R |
NTSC/PAL Waveform Monitor. User selectable display for line, field and sync. two inputs, variable vertical gain |
720 |
Tektronix |
1503B |
Metallic cable TDR. Find faults in coaxial cables up to 50,000ft. long. |
721 |
Tektronix |
1503C |
Metallic cable TDR. Find faults in coaxial cables up to 50,000ft. long. Option 04 (YT-1 Printer) |
722 |
Tektronix |
1710B |
Waveform Monitor for NTSC systems.. |
723 |
Tektronix |
1720 |
Waveform Monitor/Vectroscope. NTSC.. |
724 |
Tektronix |
1725 |
NTSC/PAL Waveform Monitor/Vectroscope.. |
725 |
Tektronix |
1730 |
Waveform Monitor. Dual channel, Microprocessor control. Front panel setup memory. |
726 |
Tektronix |
1730D |
Waveform Monitor. Dual channel. Computer interface.. |
727 |
Tektronix |
1735 |
Waveform Monitor. Dual system; NTSC/PAL. . |
728 |
Tektronix |
1740 |
Waveform Monitor/Vectroscope and Phase display. NTSC. |
729 |
Tektronix |
1750 |
Waveform Monitor/Vectroscope and Phase display. NTSC. |
730 |
Tektronix |
1751 |
Waveform Monitor/Vectroscope and Phase display. PAL system |
731 |
Tektronix |
1780R |
Video measuring system; Waveform Monitor & Vectroscope. NTSC. |
732 |
Tektronix |
5A22 |
Differential amplifier plug-in for the TEK 5000 series oscilloscopes. Hi pass-Low pass filter |
733 |
Tektronix |
5S14N |
1 GHz Time equivalent sampler for 5000 series. Rise time <350pS, Dual ch., 2V p-p max |
734 |
Tektronix |
7A13 |
Differential comparator for Tektronix 7000 series oscilloscopes.. |
735 |
Tektronix |
7A24 |
350 MHz dual channel vertical amplifier for 7000 series oscilloscopes. 5mV to 5V per/div. |
736 |
Tektronix |
7S11 |
Sampling unit which accept diffirent types of sampling heads. t |
737 |
Tektronix |
K212 |
Oscilloscope cart. Fits TEK 2400, TDS series and many other types of equipment. |
738 |
Tektronix |
K218 |
Equipment cart. 3 shelfs. |
739 |
Tektronix |
11A34 |
Vertical amp pluig-in for 11XXX and DSA series oscilloscopes. 4 channel |
740 |
Tektronix |
11A71 |
Vertical amp pluig-in for 11XXX and DSA series oscilloscopes. |
741 |
Tektronix |
AM503A |
Current probe amplifier with TM502A chassi. For TEK A6302, A6303 probes. |
742 |
Tektronix |
A622 |
Current probe AC/DC, 100kHz BW, 50mA-50A max. For DMM’s and oscilloscopes |
743 |
Tektronix |
P2200 |
200MHz x1/x10 passive probe for any oscilloscope. New with complete set of accesories |
744 |
Tektronix |
P2220 |
200MHz x1/x10 passive probe for any oscilloscope. New with complete set of accesories |
745 |
Tektronix |
P5100 |
High voltage oscilloscope probe x100 with complete set of accesories |
746 |
Tektronix |
P5200 |
High voltage differential probe. 25MHz, 1300V, 10MOhm, 4.7pF input. x50/x500 attenuation. With power supply and clips |
747 |
Tektronix |
P6109 |
150 MHz probe, Rugged modular construction. 11.8pF. For any oscilloscope. With accessories |
748 |
Tektronix |
P6015 |
HV probe. 40kV max. measurment. Works with any oscilloscope. Probe will be charged with dialectric fluid before shipment. |
749 |
Tektronix |
P6046 |
Differential probe. 100MHz BW, CMRR: 10,000 @ 50kHz.. COMPLETE set of hard to find accesories. a001 |
750 |
Tektronix |
P6130 |
250 MHz probe, 10.8pF, x10, 1.5m long. For any oscilloscope |
751 |
Tektronix |
P6133 |
150 MHz probe, 11.4pF, x10, 1.3 or 2.0m long. For any oscilloscope |
752 |
Tektronix |
P6138 |
400 MHz general purpose oscilloscope probe for 1MOhm oscilloscope inputs, x10. With standard accesories |
753 |
Tektronix |
P6139 |
500 MHz general purpose oscilloscope probe for 1MOhm oscilloscope inputs, x10. With standard accesories |
754 |
Tektronix |
P6562 |
SMT oscilloscope probe. 350MHz BW, x10 attenuation. With accesories and storage case |
755 |
Tektronix |
P6202A |
500MHz FET probe for 50 Ohm or 1 MOhm systems. 2pF input capacitance. Dynamic range +/-6.0V ( 60V with external attenuator). 10x attenuation. DC Offset nulling. |
756 |
Tektronix |
P6106A |
250MHz, x10 oscilloscope probe. With ground lead and Spring Hook tip. Lenght: 2m |
757 |
Tektronix |
P6230 |
1GHz active probe for use with any oscilloscope. Tektronix probe pwr jacks. TEK1101A P/S required if no jacks available |
758 |
Tektronix |
P6467 |
High speed probe adapter for the TLA520 series logic analyzers |
759 |
Tektronix |
S-3A |
Sampling head DC- 1GHz with probe. Rin= 100kOhm, <2.3pF. Complete set of accesories. |
760 |
Tektronix |
S-4 |
Sampling head DC-14GHz for Tektronix 7S11 or 7S12 plug-ins |
761 |
|
S-6 |
Sampling head DC-11.5GHz for 7S11 or 7S12 plug-ins. ii |
762 |
Tektronix |
SD-26 |
Sampling head DC-26.5GHz. |
763 |
Tektronix |
S-52 |
Pulse generator head 25pS rise time for Tektronix 7S11 or 7S12 TDR ii |
764 |
Tektronix |
TD100 |
Data managment computer for the Tektronix TDS series oscilloscope family. Adds hard drive storage thru an oscilloscope GPIB interface. |
765 |
Tektronix |
067-0484-01 |
Deskew fixture for the TEK P6246, P6247, P6248 probes. |
766 |
Tektronix |
015-0310-01 |
Comparator Head for use with Tektronix calibration plug-ins |
767 |
Tektronix |
016-1166-00 |
Rack mount kit for the Tektronix TDS 300 & TDS 400 series oscilloscopes |
768 |
Tektronix |
PS2510G |
0-36V, 0-3.5A, GPIB programmable.. |
769 |
Tektronix |
PS501-1 |
Precision power supply. 0-20 V with 10mV resolution setting 0-400mA, 5VDC @ 1A fixed output. For TEK TM series chassies |
770 |
Tektronix |
PS503A |
2 of 0-20V @ 0-1A max and 5V @ 1A. Tracking mode. For TEK TM500/5000 chassis only |
771 |
Tektronix |
PS280 |
2 of 0-30V @ 0-2A max and 5V @ 3A. Tracking, Parallel, Series modes on 30V outputs.. |
772 |
Tektronix |
GB1400 |
GigaBert Tester and Generator. Computer interface. Internal or external clock mode |
773 |
Telebyte |
453 |
Transmission line simulator. From 500 to 18500 feet. Remote control capability |
774 |
Teltone |
TLS-4 |
Telephone line simulator. 4 simulated phone lines with 2 simultaneous independent conversations. Add your own audio signal. Test dialing, ringing, ringback, busy tone response and much more. |
775 |
Teltone |
TLS-4A-01 |
Telephone line simulator. 4 simulated phone lines with 2 simultaneous independent conversations. Add your own audio signal. Test dialing, ringing, ringback, busy tone response and much more. |
776 |
Tenma |
72-7210 |
5MHz Sweep-Function generator with frequency counter. 1:1000 Sweep control (10mS-5sec), Pulse function, 20dB attenuator, DC offset. Measure frequency up to 50MHz with internal counter. |
777 |
Topward |
TFG 4613 |
12 MHz function generator, Sine, Square, Triangular, Pulse. AM/FM/Sweep functions, dual output, Variable symmetry. Clone of the HP 3312A |
778 |
Topward |
TPS-3000 |
Dual 0-30V, 0-2A output with tracking function. Four separate meters for simultaneous monitoring of voltage and current |
779 |
Topward |
TPS-4000 |
2 of 0-30V @ 6A each. Four analog meters for simultaneous monitoring of voltage & current, Tracking mode, ture |
780 |
Topward |
6303A |
2 of 0-30V @ 6A ea., 5V @ 5A. Four analog meters, Tracking mode, CV or CC mode. |
781 |
Topward |
6306D |
2 of 0-30V @ 6A ea., 5V @ 5A. Digital meters, Tracking mode, CV or CC mode. |
782 |
Transistor Devices |
DLP50-60- 1000A |
1000Wt, 60A, Static or dynamic mode. Three current ranges: 6, 18, 60A. |
783 |
Transistor Devices |
DLP50-20-100 |
Electronic load with LCD displays. Hi/Lo range, Constant current or constant voltage mode. Available in a rack of 4 units |
784 |
TTC |
PR-40A |
Portable Thermal printer. For use with TTC analyzers |
785 |
TTC |
224 |
Protocol analyzer with options 11704 ENH ESF/SLC, 41500 T1/FT1/DDS BERT, 12041 G.821 PERF, 12042 ADV STRESS PAT, 13963 SMRT Loopback, 42659 DSP opt BD, 12708 Digital Analysis, 12709
SS7/ISDN mon, 13964 Caller ID, 14875 VF, 41934 Signalling |
786 |
TTC |
310 |
Protocol analyzer with DS1/DS3 interface; opt 1 and 3 |
787 |
TTC |
2000 |
Bit Error Analyzer. Up to 64 kBaud. With RS-232 interface. |
788 |
TTC |
4000 |
Communication analyzer. Two interface slots allow mixing of different test modules in one analyzer. |
789 |
TTC |
6000A |
Communication analyzer. Inteface modules are available separately |
790 |
TTC |
6005 |
GPIB Inteface module for TTC6000A analyzer |
791 |
TTC |
40200 |
RS-449 interface for the TTC 4000, 6000 analyzers iii |
792 |
TTC |
40202 |
V.35 Interface module for TTC 4000, 6000 analyzers |
793 |
TTC |
40204 |
Interface module for TTC 4000, 6000 analyzers |
794 |
TTC |
40849 |
T1 channel monitor and lid for the TTC209. |
795 |
TTC |
41440 |
T1/FT1 interface for the TTC6000 analyzer. Unused condition |
796 |
TTC |
41440A |
T1/FT1 interface for the TTC6000A analyzer. |
797 |
TTC |
41704-01 |
V35 inteface plug-in for TTC 6000 |
798 |
Valhalla |
2101 |
W-A-V meter. Wide band AC or DC up to 300V, 20A. Low range 200mA. |
799 |
VEB RFT |
PSI 202 |
Sound level meter. Impulse, Fast, Slow response. 17 to 140dB, 20Hz to 40kHz. Vibration analisys (accelerometer required). Filter port allow band measurements. |
800 |
Velonex |
510 |
Surge Transient generator. Connects directly to AC mains and generates up to 2.5kV transients. |
801 |
Wavetek |
8501 |
RF Peak Power meter. Works with Gigatronics power sensors.. wj |
802 |
Wavetek |
8531 |
RF Power meter. Measure power up to 26GHz. GPIB, Analog and digital display. W/o sensor |
803 |
Wavetek |
22 |
11 MHz Frequency stabilized Sweep/Function Generator. Frequency accuracy is 0.09% over its 100 Hz to 11 MHz. LCD display, Lin/LOg sweep, 20V p-p, 6 functions, small size |
804 |
Wavetek |
131 |
2MHz Function Gen. with Freq. control by ext.voltage, 50/600Ohm output, -60dB to +10dB |
805 |
Wavetek |
180 |
2MHz Function Gen. with Sweep control. Standard waveforms plus var. symmentry |
806 |
Wavetek |
186 |
Phase lock generator. 0.0001Hz to 5MHz, phase lock to external frequency. Rack mount case. |
807 |
Wavetek |
275 |
Function-Arbitrary waveform generator. 10mHz-12MHz, Record length 8192 points (opt 4) |
808 |
Wavetek |
288 |
20MHz Synthesized Function Generator, 30V p-p output, FM/AM/Sweep/Phase Angle. |
809 |
Wavetek |
955 |
Signal source 7.5-12.4 GHz, +10dBm, +/-0.1dB flatness, 25dB control range, Long term stability: 0.009%, Harmnonics: <-20dBc, Spurios noise: -55dBc. internal AM/FM modulation, Sweep or CW. External power leveling and Phase lock |
810 |
Wavetek |
1084 |
3500-4500 MHz Sweep/CW generator with digital readouts.+13dBm to -60dBm.. |
811 |
Wavetek |
680-3 |
100 MHz Pulse Generator Modules. Add channels to your Wavetek 869 modular pulse gen. |
812 |
Wavetek |
802 |
50MHz Pulse Generator. 5nS Rise/Fall time. Rack mout case option. |
813 |
Wavetek |
EH2000 |
200MHz max repetition rate. 1nS rise time, 5V p-pk into 50Ohms. Fully programmable |
814 |
Wavetek |
1391 |
50MHz Pulse generator. VXI chassi.. BEST PRICE |
815 |
Wayne Kerr |
3245 |
Impedance Analyzer. Can test transformers and large value inductors. Option BCI-A installed |
816 |
Weinschel |
3T-10 |
10dB Attenuator. DC-12.4GHz, SMA (f/m). NEW! QIII |
817 |
Weinschel |
3T-20 |
20dB Attenuator. DC-12.4GHz, SMA (f/m). NEW! QII |
818 |
Weinschel |
33-20-12 |
3dB, 50Wt Attenuator. DC to 8.5GHz, 3.5mm connectors. |
819 |
Weinschel |
33-3-12 |
20dB, 50Wt Attenuator. DC to 8.5GHz, 3.5mm connectors. |
820 |
Weinschel |
5872 |
DC-20GHz, 0-90dB step attenuator, 24V. |
821 |
Weinschel |
152A-70-1 |
DC-26.5GHz, 70dB step attenuator, 24V. |
822 |
Weinschel |
167-110 |
DC-18GHz, 110dB step attenuator, 24V. |
823 |
|
ANT-20 |
Advanced netwok tester. Contact for list of options |
824 |
WG |
ANT-20SE |
With STM-64 and OC-192 Inteface module. Contact us for the list of installed options. |
825 |
WG |
ANT20SE |
With STM-64 and OC-192 Inteface module. Contact us for the list of installed options. |
826 |
WG |
2262/90.1 |
Acterna E1/T1 Module for the Acterna 8630 analyzer |
827 |
WG |
PKN-1 |
Transmission Line simutaltor. 10kHz to 10MHz, 75Ohm impedance. BNC connectors |
828 |
WG |
PA-20 |
Portable PCM channel analyzer. Complete with accesories and carring case. |
829 |
WG |
BN9305/00.17 |
Wan Analyzer module for DA-30 analyzer |
830 |
WG |
BN7511/00.18 |
ISDN BRA Line interface for DA-30 analyzer |
831 |
Wiltron |
560 |
Scalar network analyzer, 10MHz to 40GHz. Three input channels. Detectors available |
832 |
Wiltron |
562 |
Scalar network analyzer, 10MHz to 40GHz. Four channels. Detectors are available. |
833 |
Xantrex |
XFR7.5-140 |
0-7.5V, 0-140A. Only 1.5″ tall. |
834 |
Xantrex |
XHR7.5-130 |
0-7.5V, 0-130A, with opt M9B (RS-232C), Constant current or voltage mode. High efficiency, small footprint. |
835 |
Xantrex |
XTS15-4 |
0-15V, 0-4A Constant current or voltage mode. With opt GPIB-M |
836 |
Xantrex |
HPD15-20S |
0-15V, 0-20A Constant current or voltage mode. Digital display with analog bargraph. |
837 |
Xantrex |
XTS60-1 |
0-60V, 0-1A Constant current or voltage mode. Digital display with analog bargraph |
838 |
Xantrex |
XTS60-1 |
0-60V, 0-1A Dual output. Constant current or voltage mode. Digital display with analog bargraph. |
839 |
Xantrex |
XTS250-0.25 |
0-250V, 0-250mA. Constant voltage or current mode. 3 1/2 digit digital meters |
840 |
Xantrex |
6060D |
0-60 @ 0-1A dual output.. Same as two Xantrex XTS60-1 mounted in one chassi. |
841 |
Yokogawa |
321345A |
Insulation tester. Measure up to 2000 MOhm, 1000V test voltage. Carrying case |
842 |
Yokogawa |
2404-15 |
Insulation tester Megohm meter.Up to 2000 MOhm, 300VAC test voltage, Handcrank generator, no batt or AC power needed to do the testin Dim: 7″x4x4. Carrying case |
843 |
Yokogawa |
700988 |
400MHz, 10MOhm, x10 oscilloscope probe. 600V max |